Solid-State Bassheads

• Compact and light
• Transistor circuit
• Class D power amplifier
• Power: 200 W at 4 ohms / 130 W at 8 ohms
• 3-Band EQ with +/- 15 dB cut / boost per band
• 6.35 mm Headphone output for silent practice
• Balanced Post-EQ XLR DI output with switchable ground lift
• Input impedance of more than 10 MOhm offers maximum sensitivity for passive pickups
• Front controls for gain, bass, middle, treble, master
• Rear ground lift switch
• Rear power on / off switch
• Front connections for instrument input (6.35 mm mono jack) and headphone output (6.35 mm stereo jack)
• Rear connections for Mains In (IEC power socket), Speaker Out (6.35 mm mono jack) and balanced XLR DI output
• Input voltage 220 - 240V AC
• Dimensions (L x W x H): 170 x 118 x 45.5 mm
• Weight 0.96 kg
• Includes power cable with EU plug

Note: Register your product at https://shop.warwick.de/en/warrantyregistration and extend the guarantee to 4 years.

• Power: 500 Watt @ 4 Ohm, 250 Watt @ 8 Ohm
• Controls for Gain, Drive, Mid Frequencies, Mid Level, Bass, Treble, Master Volume
• Pre/Post Switch
• Connections: Balanced Out, Effect Loop, Tuner Out and 2x Speaker Twist speaker outputs
• Dimensions (W x D x H): 27,3 x 21,6 x 7 cm
• Weight: 2 kg

• Power: 700 W @ 4 Ohm or @ 2.67 Ohm, 350 W @ 8 Ohm
• Transistor preamp
• Class D amplifier
• Gain, Drive, Mid Freq 180 - 1,000 Hz controls
• Treble +/- 14 dB @ 4,000 Hz
• Mid Level +/- 16 dB
• Bass +/- 17 dB @ 40 Hz
• Master volume
• Input for passive and active basses
• Serial effects loop
• Speaker outputs: 2x Speaker Twist
• DI-Out with pre/post EQ and ground lift switch
• Tuner output
• Dimensions (W x D x H): 30 x 23 x 8 cm
• Weight: 2.22 kg

• Power: 800W @ 4 or 2Ω, 400W @ 8Ω
• Class D amplifier with 8/4 or 2Ω impedance switch for optimum adjustment
• Active / passive switch
• Preamp: Input gain with clip indicator (O.D. LED)
• Variable voicing controller: Flat to Vintage Scoop
• Active 4-Band EQ: +/- 12 dB for bass, low-mid, high-mid, treble
• Deep switch for extra-low-end bass boost and master volume
• Balanced XLR output with pre / post, line / mic and ground lift switches
• LEDs for protect and limit
• 2 Speaker Twist outputs
• Dimensions (H x W x D): 8 x 27 x 29 cm
• Weight: approx. 2.5 kg
• Incl. gigbag and strap
• Made in USA

• Power: 300W @ 4Ω or 180W @ 8Ω
• Clean channel with gain control
• Distortion channel with gain shape and level controls
• 7-Band graphic EQ with FBQ spectrum analyser
• Ultra bass switch
• Integrated compressor
• Dual foot switch for channel selection and ultra-bass function
• Headphone output
• Balanced XLR DI and line outputs
• CD input
• Effect input
• Dimensions (W x H x D): 450 x 117 x 225 mm
• Weight: 3.5 kg

Markbass Little Mark 58R; Solid State Amplifier Head for Bass Guitar; Housing made of lightweight, environmentally friendly materials; bi-band limiter; tone selector: Flat/Scooped Mid/FSW (footswitch);; Channels: 1; Power: 500 W @ 4 Ohm, 300 W @ 8 Ohm; Controls: Gain, Low, Mid/Low, Mid/High, High, Master, Line Out, Old School; Switches: Pre/Post EQ, Ground Lift, Mute, Power, three way switch: Flat/Scooped Mid/FSW (Sound selection can be called up via foot switch); Effect Loops: Seriell; Connections: Input (1/4" Jack), Effects Send & Return (2 x 1/4" Jack), Mute Footswitch (1/4" TRS-Jack), Line Out (XLR); Speaker Outputs: (2 x 1/4" Jack & Speaker Twist @ 4-8 Ohm); suitable foot switch: Item no. No.: 512098 (not included in delivery); Dimensions (W x D x H): 276 x 256 x 83 mm; (10,87" x 10,08" x 3,27"); Weight: 2 kg (4,4 lbs); Made in Italy

• Lightweight aluminium construction
• Solid state design
• Power: 350 watts at 4 ohms / 200 watts at 8 ohms
• Noiseless fanless cooling system
• Class A low-noise preamp
• Class D power amp
• 5-Band EQ with +/- 18 dB boost/cut per band
• Series FX loop
• Front panel controls: Lo-Bass, Hi-Bass, Mid, Lo-Treble, Hi-Treble, Input Level, AUX Level and Volume
• Front panel 3-way toggle switch for mute / active / passive
• Front panel limiter toggle switch
• Back panel pre/post EQ toggle switch
• Back panel balanced line out switch
• Back panel ground / lift switch
• Power switch
• Front panel connectors for instrument input (6.3 mm mono jack)
• FX send / return (2 x 6.3 mm mono jack)
• Preamp output (6.3 mm mono jack)
• AUX input (3.5 mm stereo jack)
• Headphone output (3.5 mm stereo jack)
• Back panel connectors for line in (6.3 mm mono jack)
• Line output (6.3 mm mono jack), DI output (XLR)
• Speaker output (2-pin Neutrik Speakon)
• IEC cold device plug
• Input voltage: 100/240V AC
• Dimensions (W x H x D): 244 x 193 x 43 mm
• Weight: 2.7 kg
• Includes power connection cable with EU plug
• Includes a gig bag
• Colour: Black

• Power: 250W into 4Ω, 180W into 8Ω
• Tube emulation & solid-state precursors
• Bass & treble contour controller
• 10-Band graphic EQ
• Adjustable compressor
• Passive / active input jacks
• DI-out with pre / post switch
• Useable in racks
• Dimensions: 44 x 9 x 33 cm
• Weight: 15.2 kg

• 1 Channel
• Power: 500 W
• High efficiency custom designed class D power amplifier
• Integrated alpha omega distortion
• Speaker simulation with three slots for high-resolution impulse responses for headphones and balanced XLR DI output
• One button compressor with intelligent make-up gain
• New low-noise graphical equaliser
• Controls: Compressor, drive, level, mod, blend, 6-band graphical EQ, master
• Switches: Passive/active, distortion on/off, bite on/off, growl on/off, mute, cab select, ground lift
• Effects: Alpha omega drive
• Min. speaker impedance: 2 Ohm
• Serial effects loop
• Dimensions (W x D x H): 230 x 180 x 71 mm
• Weight: 2.4 kg
• Made in Finland

Connections:

• Input: 6.3 mm jack
• DI output: XLR
• FX send / return: 2x 6.3 mm jack
• Aux input: 3.5 mm stereo jack
• Headphone output: 6.3 mm stereo jack
• Footswitch: 6.3 mm jack
• USB-C
• Speaker output: Speaker twist

GR Bass Pocket 50 Bass Top; rechargeable 50W bass amp; 4 ohms; 8 hours playtime; built-in audio interface and DI out; Front panel: Gain, Pre/Post DI, Low, Mid Low, Mid High, High, Mute, Master; Rear panel: USC Type C, Output, 30V DC 3A, Phone, DI, Aux IN, Input; dimensions: W 6.4 x D 3.9 x H 1.97 inch (W 16.3 x D 9.9 x H 5 cm); Weight 0.75KG; Made in Italy.

• Extremely compact and lightweight
• Channels: 1
• Power: 200W
• Controls: Gain, Bass Middle, Treble, Master
• Input (6.3 mm jack)
• DI out (XLR)
• Headphone output (6.3 mm stereo jack) with speaker simulation

• Compact and lightweight bass amp head with Mosfet preamp and thrust compressor
• 1 Channel
• Power rating: 250 W
• Controls: Gain, Thrust Compressor, Bass, Lo-Mid, Hi-Mid, Treble, Master
• Switch: Passive/Active
• Compressor On/Off
• DI Pre/Post Eq
• Dimensions (W x D x H): 255 x 233 x 69 mm
• Weight: 2.3 kg

Connections:

• Input: 6.3 mm jack
• DI Output: XLR
• AUX input In: 3.5 mm stereo jack
• Headphones: 3.5 mm stereo jack

• 1 Channel
• Power: 900 Watt
• Dual-drive engine with mod control for infinitely adjustable (no fixed increments or steps) combination of alpha and omega drive circuits
• Latency-compensated post DI with digital speaker simulation
• Headphone output with speaker simulation
• Three impulse response slots selectable via cab select switch
• Adjustable VCA compression at studio quality
• Controls: Comp, drive, level, mod, blend, gain, master, headphone volume
• Switch: Input passive/active, distortion, bite, growl, mute, impedance: 4/2 Ohm, GND lift, cab select
• Dimensions (W x D x H): 267 x 254 x 70 mm
• Weight: 2.9 kg
• Includes intelligent footswitch
• Made in Finland

Connections:

• Input: 6.3 mm jack
• DI out: XLR
• FX send & return: 2x 6.3 mm jack
• Aux in: 3.5 mm stereo jack
• Headphone output: 6.3 mm stereo jack
• Pre & post DI out: 2x XLR
• MIDI in
• Footswitch input: 6.3 mm jack
• Micro USB

Bundle offer comprising

• Bass Amp HeadSince its launch in 1969, there is no alternative to the original SVT from Ampeg. The classic convinces with its unique sound and its "tube-strong" 300 Watt output power.

Now, almost four decades later, Ampeg introduces a mini-version of the legendary amplifier, which was launched under the name of SVT Micro Head. It is ideal for smaller stages and sound studios, where an original SVT would be too big and too loud.

The Micro Head is visually linked to the original SVT - with the silver front plate, the black cover, the chrome-plated corners and the silver-blue face plate, the SVT Micro Head clearly makes it clear that it is not a toy. Despite its small dimensions of 14 cm (height), 30 cm (width) and 25 cm (depth), the head has a real Ampeg preamp and a strong 200 watt transistor output stage.

For recording sessions, the SVT Micro Head has an Aux-Stereo input, which is mixed with the main input and sent to the headphone output. This feature allows the musician to listen to a click or guide track at the same time, record the direct signal from the "pream-out" and remove the amplifier via a microphone. For live applications, the familiar Ampeg Preamp controls include 15 dB pad, gain, bass, ultra-mid, treble, volume and limiter defeat, allowing the musician to quickly and effectively find the desired sound. The world-wide switching power supply and the compact dimensions make the amp the ideal travel companion.

• 200 W RMS at 4 ohms
• Transistor preamp
• MOSFET output stage
• Aux stereo input (can be mixed with main input and be sent to the headphone output)
• Suitable for click or guide track
• Controls for 15 dB pad, gain, bass, Ultra-Mid, Treble, Volume and Limiter Defeat
• Silver faceplate
• Black reference
• Chrome corners and silver blue mesh fabric
• Switching power supply for worldwide use
• Dimensions (H x W x D): 304 x 140 x 254 mm

• Bass Cabinet
• Equipped with: 2 x 10" Eminence speakers
• Power rating: 200 Watt RMS at 8 Ohm (mono)
• Portable alternative to the full-size SVT cabinet
• Frequency range (-3 dB): 58 - 5,000 Hz
• Usable low frequency (-10 dB): 40 Hz
• Dimensions (H x W x D): 610 x 330 x 280 mm
• Weight: approx. 14 kg

• The sssnake PPS 1015
• 1.5 m Speaker cable, 2 x 1.5 mm² cross section
• 6.3 mm Jack - 6.3 mm Jack
• Suitable for passive speakers - not for active speakers

• Power: 500W at 4Ω, 300W at 8Ω (Speaker Twist)
• Class D amplifier
• Active 4-Band EQ
• Button" controller
• Tuner output
• Mute switch
• Transformer balanced DI (pre- & post switchable) with ground lift
• Serial effects loop
• Line out
• Line in
• 3.5mm AUX-In
• 3.5mm Earphone terminal
• 115/230 V/AC switchable
• Dimensions (W x H x D): 27 x 4.5 x 21 cm
• Weight: 1.49 kg
• Made in Germany
• Matching 19" rack ears, and soft bag available (not included)

• 1 Channel
• Class D power amplifier
• Output power: 500 W
• Minimum of 4 Ohm total
• FX loop
• Compressor
• Foot switchable
• DI output
• 2 Speaker outputs
• 3-Band tone control with semi-parametric midrange control
• Dimensions (W x H x D): 27.6 x 8.5 x 25.1 cm
• Weight: 2.95 kg
• Colour: White

Markbass Nano Mark II Head, top for electric bass guitar, 300 watts at 4ohms, intiutive user interface, integrated bi-band limiter, controls for gain, master, low, mid low, mid high, high, clip LED; inputs: input (6,3 mm jack), outputs: line out XLR with pre/post EQ switch, ground lift switch, effect path (2x 6.3 mm jack), foot switch for flat/scooped-mid(6.3 mm jack), speaker out speaker twist, dimensions: 20 cm x 5.3 cm x 21 cm (W,H,D), weight: 1.45 kg, footswitch is not included.

• Compact and lightweight amp head with Mosfet preamp and thrust compressor
• 1 Channel
• Power rating: 500 W
• Controls: Gain, Thrust Compressor, Bass, Lo-Mid, Hi-Mid, Treble, Master
• Switch: Passive/Active
• Compressor On/Off
• DI Pre/Post Eq
• Dimensions (W x D x H): 255 x 233 x 69 mm
• Weight: 2.3 kg

Connections:

• Input: 6.3 mm jack
• DI Output: XLR
• AUX input In: 3.5 mm stereo jack
• Headphones: 3.5 mm stereo jack