ART

• Completely passiv design
• 8 Transformers to separate input and output signal grounds
• Noises caused by ground loops are suppressed by separation of the two signal paths
• In and outputs with XLR, 6.3 mm jack and RCA jacks
• Mass separation of input and output signal reduces hum
• Transformers with extremely linear frequency response and wide frequency range
• Can be used for signal tapping or as a splitter
• All-metal housing
• Removable rack mount bracket. 19"/ 1U

• 8 Stereo input channels
• Controller for input levels
• Panorama and effect send on each channel
• External effects loop with send and return control
• 8 Stereo jack inputs 6.3 mm (L / (R)
• Switchable XLR balanced Mic input / jack input 6.3 mm to channel 1
• 48 V phantom power
• Signal and clip LEDs
• 2 Balanced XLR line outputs
• Stereo headphone output
• Internal power supply
• Format: 19 "/ 1U
• Dimensions: 44.5 x 483 x 152 mm
• Weight: 2.95 kg

• With stereo outputs
• 8 Mono channels
• 8 Independent input channels
• Controls for input levels and panning on each channel
• Balanced XLR- and unbalanced jack inputs on each channel
• 48 V Phantom power on each XLR input (selectable via DIP switch on the rear side)
• Master output with balanced jack connectors and master level control
• Unbalanced prefade outputs (RCA unaffected by the master level control), and AUX bus inputs (to connect several devices together)
• Strong 19" housing (1 U) with internal power supply

• The Promix mix 3 microphone signals (XLR) to 1 mono signal
• Maximum Gain + 60 dB
• Input impedance 600 Ohm
• Maximum input level -14 dB
• Maximum output level +14 dB
• Output impedance 600 Ohm
• Total harmonic distortion > 0.02%
• With headphone port
• 12 V Phantom power
• Dimensions: 143 x 92 x 45 mm
• Weight: 680 g
• Including 12V DC power adapter

• From eight symmetrical microphone signals (low impedance) -> 16 microphone signals (8 pairs)
• Direct output and a galvanic isolated output per transformer on each channel
• Transit of phantom power to the main output
• Ground-lift switch for the isolated output
• Switchable attenuation (pads) on each input
• Format: 19" / 1U

• Phase reverse switch
• Galvanic isolation of the channels
• Ground lift switch
• Main Mic Input XLR
• Isolated mic input / merger XLR
• Mic Main Out XLR
• Isolated Mic Out / Splitter XLR

• 5 Zone mixer / distributor
• Adjusts volume of multiple amplifiers or active monitors separately
• Stereo/mono switch + clip and 5 segment LED on each zone
• Connectors: 4x line in XLR (2x L/R), 10x XLR Out (5x L/R)
• Dimensions: 482 x 152 x 44.5 mm (19"/1U)
• Weight: 2.4 kg

The SLA-2 is a 1 RU 19" power amplifier that is suitable for studio and live applications thanks to its SmartFan silent cooling system, meaning that the following fields of application are possible: project, home and recording studios, broadcasting/radio/TV, live/PA area, DJ sound systems, permanent/fixed installations, churches, clubs and rehearsal room PA systems. Alongside its excellent sound with minimal interference and unwanted noise, the ART SLA-2 offers the following features:

• 200 Watt RMS at 8 Ohm per channel
• 280 Watt RMS at 4 Ohm per channel
• 560 Watt RMS at 8 Ohm bridged
• Frequency range: 10 Hz to 40 kHz +/- 0.5 dB
• CMMR: > 60 dB (typical @ 1 kHz)
• THD:
• Toroidal transformer
• Balanced XLR / unbalanced 6.3 mm jack inputs
• Weight: 9 kg

• Six independent headphone amplifiers with high output power
• Possibility of simultaneous use of up to 18 headphones
• Three headphone outputs on every channel: one on the front side, two on the back side
• Stereo aux input on every channel (front side), balance/mix control on every channel featuring twofold usage
• More selectable monitor settings on every channel: Stereo, mono left, mono right, mono left + right
• 4 Segment LED level indicator and volume control on every channel
• Level control and 8 segment LED level indicator on the main input
• Direct input on the front side
• XLR- and jack inputs and -outputs (to connect several devices)
• Design: 19", 1 U

• Frequency range: 10 Hz -50 kHz
• THD: 0.01% Typical @ 1 kHz
• Input: unbalanced jack
• Input impedance 50 kOhm
• Output: XLR male
• Output impedance 600 Ohm
• Switchable low pass filter -3 dB @ 30 kHz
• PAD switch (0dB, -20dB, -40dB)
• Phase switch (normal / invert)
• Switchable ground lift
• Dimensions: 44.5 x 107 x 89 mm
• Weight: approx. 340 g

• Discrete Class-A
• Adjustable input impedance (150 - 2400 Ohm)
• Adjustable anode voltage
• 2x XLR mic inputs
• 2x 6.3 mm Jack instrument inputs
• Balanced XLR and jack outputs
• Switchable phantom power: 48V
• High pass filter
• Large VU meter
• Backlit meters
• Supports M/S decoding matrix
• Design: 19" / 2U
• Dimensions (H x W x D): 88 x 482 x 222 mm
• Weight: 4.7 kg

• Passive
• Four stereo input channels
• Stereo output (all 6.3 mm jack connectors are stereo - tip, ring, sleeve)
• Dimensions: 47 x 117 x 104 mm
• Weight: 380 g

• Frequency range: 10 Hz –100kHz
• Max. output level: +6 dBu (battery powered) / +14 dBu (phantom powered)
• Max. input level: +4/+24/+44 dBu
• Dynamic range: > 100 dB
• Input: Jack and XLR female
• Input impedance 470 Ohm
• Output: XLR male
• Output impedance
• THD:
• Switchable low pass filter -3 dB @ 30 kHz
• PAD switch (0dB, -20dB, -40dB)
• Phase switch (normal / invert)
• Switchable ground lift
• Power requirements : 9V battery or phantom power
• Dimension: 44,5 x 107 x 89 mm
• Weight: 340 g

Bundle offer comprising

• 5-Channel Small Mixer and USB Audio Interface
• 16 Bits, 44.1/ 48 kHz
• 2 Balanced XLR mic inputs
• 1 Instrument input 6.3 mm jack
• Stereo line input 6.3 mm jack (mono usable)
• 6.3 mm Jack stereo output
• Headphone output
• Switchable 48 V phantom power
• LED for signal/ clip display
• Control room output
• Dimensions (H x W x D): 82 x 195 x 245 mm
• Weight: 2.5 kg
• Including USB cable and power supply

• Mixercase
• Case suitable for ART TubeMix
• 1 Snap lock
• 2 Metal hinges
• 1 Plastic carrying handle
• Aluminium edges
• Interior with EVA
• Foam on top cover
• Inside space for accessories
• Inner dimensions (W x D x H): 160 x 70 x 75 mm
• Outer dimensions (W x D x H): 262 x 357 x 135 mm
• Weight: 1.65 kg
• Colour: Black

• Optical compressor
• Attack and Release controls separately
• 4-band EQ with 2 parametric mids
• Bypass for compressor and EQ
• Loop between preamp and compressor as well as compressor and EQ
• +4/-10 dB switchable output level
• VU meter
• 1/4" jack instrument input
• Mic input XLR
• Line output balanced XLR and 1/4" unbalanced jack
• 19" 2U
• Dimensions: 89 x 483 x 233 mm (HxWxD)
• Weight: 5 kg

• 70 dB Gain
• FET Limiter
• Selectable input impedance
• LED Metering
• +48V phantom power
• XLR and jack inputs and outputs
• Switchable phase invert
• Switchable low cut filter
• Variable input and output controllers
• Dimensions: 44.5 x 150 x 165 mm
• Weight: 1.14 kg
• Incl. Power supply 9VAC/1A

Small plug with 2.1 mm bore

• Bass and treble separately adjustable
• 8-Segment LED chains for each channel and bus
• XLR and jack inputs are 6.3 mm balanced
• Headphone outputs front and back
• Aux input
• Format: 19", 1U

• Re-amping interface for multiple sources
• Stereo / Dual Direct Box
• Pad circuitry for mic / instrument inputs
• 2x XLR (balanced) / 1/4 "TRS line inputs
• Transformer-balanced XLR output (microphone level)
• Transformer-balanced 6.3 mm jack output (instrument)
• Frequency response: 20 Hz - 20 kHz
• Mute function
• Style: Desktop

• High-quality separation transformer, without battery
• Supports 50k Ohm input signals to 600 Ohm balanced outputs
• Switchable input attenuation (0, -20, -40 dB)
• Phase reverse switch
• Ground-lift switch (inputs are completely separated from ground and outputs)
• XLR outputs balanced
• Compact, black anodised aluminium housing
• Frequency response: 10 Hz - 50 kHz, ± 0.5 dB @ 4 dBu, THD: 0.01% typical @ 1 kHz, 18 dBu / <.05 hz dbu>
• Crosstalk attenuation:> 80 dB (typical)
• Inputs: 1/4 "TRS unsymm (2), 50 k ohms
• Parallel feedthroughs: 1/4 "TRS (2)
• Outputs: XLR male (2), 600 Ohm
• Low pass filter: switchable, -3 dB @ 30 kHz
• Dimensions (WxDxH): 99 x 117 x 47 mm
• Weight: 0.40 kg

• To convert two unbalanced channels into two symmetrical channels and vice versa
• Noise and low-distortion circuit
• XLR connectors for balanced inputs and outputs
• RCA connectors and stereo mini jacks for unbalanced inputs and outputs
• Level control for balanced and unbalanced outputs
• Illuminated on/off switch
• Robust aluminium housing
• Incl. power supply