Doepfer

• Sums up all connected input modules (article nr 399259 - not included) to a stereo sum
• AUX send and AUX return
• Width: 4 HP
• Depth: 40 mm
• Power requirements: +20 mA (+12 V) / -20 mA (-12 V)

• 5 Different waveforms
• Adjustable frequency range
• Eurorack format
• Width: 8 HP
• Depth: 55 mm
• Power requirement: +30 mA (+ 12V) / -20 mA (-12V)

• Vintage Edition with a black front panel
• Compact 4-channel mixer
• Suitable for CV and audio signals
• Volume control available per each channel
• 4 x Input
• 2 x Mix output
• Current consumption: 10 mA (+12 V) / 10 mA (-12 V)
• Width: 4 TE
• Depth: 30 mm

Thru Zero Quadrature - VCO oscillator generates sine and cosine waveforms at the same time. These are terminated as soon as the linear control voltage reaches 0V.

• Special Edition with additional output amplifier
• 2 Control sections: Linear and exponential
• Controller for XTune, XFM, LFrq and LFM
• Width: 8HP / 40.3 mm
• Depth: 60 mm
• Power requirements: 90mA
• Colour: Blue anodised front plate and white knobs

• For the A-100 modular system
• Width: 14 HP
• Depth: 60 mm
• Power requirement: +80 mA (+12 V) / -60 mA (-12 V)

The A-112 Module is a combined module of a voltage-controlled 8-bit sampler and a wavetable oscillator. Moreover, it is able to produce effects. It is available as a supplemental sound generator module for the A-100 with the characteristic sound characteristics of the early 8.Bit samplers and cannot be compared with commercially available MIDI samplers!

"Sampling mode: "

8-Bit audio resolution , 128 kB memory in 2 banks (S1, S2) of 64KB each (this corresponds to 2 seconds sampling time at 32 kHz sampling frequency), audio input with attenuator, overdrive display in recording mode (gate LED) Dump capability to archive sounds, non-volatile memory for the samples in the module, manual tune control to adjust the sampling rate during recording and playback, the CV input (1V / octave), along with the tune control The sampling rate or pitch (pitch 5 octaves corresponding to 0 ... 5V, pitch resolution 1/4 semitone), gate input (no pure trigger, but the sample is started at the positive edge and runs until the Gate input becomes "high" or the end of the sample is reached), manual gate button, unfiltered audio output (ie, quantisation sounds can be used for sound generation).

Wavetable mode:

A special form of sampling mode, with the audio input acting as a control input for the sample which is stored in one of two banks (S1, S2) with 64 kbyte of memory each. In wavetable mode each bank is arranged as 256 pages of 256 bytes. The wavetables are loaded in the sampling memory (normally loaded via MIDI dump), thus making a wavetable oscillator, in which different waveforms (with different harmonic content) are traversed by CV2. With this mode of operation, however, a "normal" sample can "pass through", which sometimes results in quite astonishing sounds (interesting for the "passing through" speech, where the language spins very extreme sound structures).

Effects:

In addition, the module offers - as a free "extra" so to speak - some effects such as delay, reverse delay, pitch shifter and freeze. It should be stressed, however, that these effects can not be compared with the result of high-quality effectors due to the 8-bit resolution and should only be understood as a free-of-charge addition for bizarre sounds.

• Combined module of voltage-controlled 8-bit sampler and wavetable oscillator
• Width: 10 HP / 50.5 mm
• Depth: 100 mm (measured from the back of the front panel)
• Power Requirements: 50mA (12V) / -20mA (-12V)

• 4 CV inputs (1x with controller, 3x without controllers)
• Width: 6 TE / HP
• Depth: 50 mm
• Power requirement: +10 mA (+12 V) / -10 mA (-12 V)

• Joystick with X-/Y-axis
• Rotation function (Z-axis) and gate button
• X-, Y- and Z-axis self-resetting via spring mechanism
• CV outputs for X-, Y- and Z-axis in non-inverted and inverted form (range: -5 V to +5 V)
• CV offset controller per axis
• 4 Quadrant CV outputs (Q1-Q4) with adjustable overlap (range: 0 V to +10 V)
• Gate output
• Current requirement: 50 mA (+12 V) / 20 mA (-12 V)
• Width: 12 HP
• Depth: 50 mm
• Joystick height: 70 mm

• Vintage Edition with black front panel
• Voltage controlled oscillator
• 3-Position toggle switch
• Linear FM input and soft-sync input
• Tune control range can be set between approx. 1/2 octave and 4 octaves via a jumper
• Width: 8 HP / 40.3 mm
• Depth: 50 mm (measured from the rear of the front panel)
• Power requirements: + 12V: 150 mA (warm up period about 30 seconds), 60 mA (continuous operation) -12V: 30mA

Module A-120 is a voltage-controlled 24 dB low-pass filter, which filters out the high frequency components from a sound spectrum while allowing the low frequencies to pass unhindered. The cut-off frequency (corner frequency) determines the point at which this effect occurs. They can be set or modulated both manually and via control voltages (filter modulation, with an LFO for example). The VCF1 is configured as a "transistor cascade" with an edge slope of -24 dB / octave, which is also used in various Moog synthesizers, This results in the typical, "legendary" Moog sound. The resonance (emphasis) can be adjusted at the VCF 1 to the point of self-oscillation. In this case, the filter operates as a sinusoidal oscillator.

• 24 dB low pass 1 (VCF1)
• Voltage-controlled 24 dB low-pass filter
• Width: 8TE / 40.3 mm
• Depth: 65 mm (measured from the back of the front panel)
• Power Requirement: 30mA (12V) / -20mA (-12V)

• Decay is adjustable manually or via external control voltage
• Envelope output is displayed with LED control
• Eurorack format
• Width: 8 HP
• Depth: 40 mm
• Power requirements: +40 mA (+ 12V) / -20 mA (-12V)

The module A-140 is a envelope generator and since it delivers control voltages, belongs to the modulation-modules. As soon as the ADSR is triggered at gate-input, it generates an adjustable control signal called the envelope. This envelope is present on its outputs in normal and inverted S-form and can be used e.g. for modulation of VCO, VCF and VCA modules as well as for transient and decay oscillations of other modules. The S-form of the envelope is unambiguously defined by four parameters, attack, decay, sustain and release. The ADSR is triggered with a gate-signal at gate-input and provides the possibility of a retrigger-Function, i.e. the envelope will be restarted every time a trigger signal is present at the retrigger-socket while the gate is active.

In connection with the comparator-module A-167 a free run "ADSR-LFO" can be realised.

• Parameters can be set independently
• 3-Step switch for selecting the time range
• Eurorack format
• Width: 8 HP
• Depth: 50 mm
• Power requirements: +20 mA (+ 12V) / -20 mA (-12V)

• 2x 84 HP
• With PSU3 power supply: +12 V / 2000 mA, -12 V / 1200 mA, +5 V / 4000 mA, 100 - 230 V
• Removable lid with carrying handle
• Steel ball corners
• Max. depth for modules in the front row: approx. 70 mm
• Dimensions (W x D x H): 510 x 420 x 210

• Generates 4 different random control voltages
• 2 outputs
• Trim potentiometers for adjusting the voltage levels
• Eurorack format
• Width: 12 HP
• Depth: 60 mm
• Power requirement: +40 mA (+ 12V) / -10 mA (-12V)
• Suitable expander module: Art.199100 (not included)

• Switchable between LFO and VCO modes
• The range of the Tune control can be changed by jumper - position 1: 16 Hz to 20 kHz, position 2: 16 Hz to 70 Hz, without jumper: 16 Hz to 22 Hz
• Width: 4 HP
• Depth: 65 mm
• Power requirements: +40 mA (+12 V) / -40 mA (-12 V)

• High-End VCO II / VCLFO
• Precise tracking over 10 octaves
• Wide frequency range: 0.5 Hz - 20 kHz in VCO mode, 0.001 Hz - 40 Hz in LFO mode
• Selector switch for LFO or VCO mode
• CV inputs with attenuators for exponential and linear FM and PWM
• Pulse width can be set
• Inputs for soft and hard sync
• Outputs available for sawtooth, square/pulse, triangle and sine wave
• Current consumption: 70 mA (+12 V) / 50 mA (-12 V)
• Black front panel
• Width: 14 TE
• Depth: 55 mm

• Eight interconnected jacks can be split into 2 groups (solder bridge on the assembly side)
• Width: 2 HP
• Vintage edition with black front plate

• VC Stereo mixer
• Mixer with 4 stereo inputs and 2 VCAs per channel
• Level control and CV attenuation per chanel
• Suitable for audio signals and voltage control
• Stereo master output
• Current draw: 40 mA (+12 V) / 40 mA (-12 V)
• Width: 8 HP
• Depth: 45 mm

• Extension module for the A-160 (Article Nr 186683)
• 8 Outputs are switched to the rhythm of the clock divider (A-160)
• Eurorack format
• Width: 4 HP
• Depth: 40 mm
• Power requirement: +20 mA (+ 12V) / -0 mA (-12V)

Note: Module must be installed directly to the right of the A-160 clock divider!

The oscillator generates sine and cosine waveforms at the same time. These are terminated as soon as the linear control voltage reaches 0 V.

• 2 Control sections: Linear and exponential
• Controller for XTune, XFM, LFrq and LFM
• Width: 8HP / 40.3 mm
• Depth: 60 mm
• Power requirements: 90 mA