Tech 21

• Analog SansAmp circuit
• Boost function (12dB)
• Compressor
• Reverb
• Delay
• Chorus
• Tuner
• Phase reverse switch
• Earphone function
• Including power supply (9 V, 200 mA)

• The same analogue SansAmp circuit, plexi distortion and delay of the first version plus some additional features, such as switch between Plexi and Cali distortion mode, an independent reverb with adjustable room size, an effects loop, tuner, XLR output and a switchable speaker simulation
• Controls: Plexi: Drive, Tone, Level - Boost - Blonde: Drive, Low, Mid, High, Level - Delay: Time, Repeats, Level - Reverb
• Buttons: Plexi / Cali, Boost Pre / Post, Speaker Sim, Delay Drift, Delay 8th, Reverb Size, Ground Lift
• LED: Effect on
• Foot switch: Plexi, Boost, Blonde/Tuner, Delay, Tap/Reverb
• Input (6.3 mm jack)
• Output (6.3 mm jack)
• Effects Loop (2x 6.3 mm jack)
• XLR out
• Power adapter connector (female connector 5.5 x 2.1 mm, negative polarity inside)
• Current consumption: 200 mA
• Power supply with a DC power adapter (Auto-Switching power adapter for voltages of 110 V-240 V with replaceable international plug for EU, UK, Australia/New Zealand included)
• Dimensions (W x D x H): 318 x 64 x 32 mm
• Weight: 587 g

Note: Battery operation is not supported.

• Two completely analogue SansAmp circuits with individual volume controls
• Drive potentiometer for gain and overdrive
• Emulated tube saturation for massive low-end bass sounds with separate volume control
• Blend control for the ratio between the SansAmp tube amplifier emulation and the direct instrument signal
• Semi-parametric EQ adjustable between 170 Hz and 3.0 kHz with cut / boost of up to 12 dB
• Tight switch for a more defined sound
• 1 MOhm jack input
• Low-impedance XLR outputs with level switch and ground lift for problem-free DI operation
• Two jack outputs with level switch
• Controls: Level 1, Blend, Mid, Drive, Treble, Bass, Mid-Shift, Level 2, Saturation
• Switch: GND, -20 dB / + 10 dB, Tight, Mute
• Status LED
• Solid metal housing
• Power supply via 18 V DC mains adapter for more headroom and clarity, 9 V mains adapter or 2 alkaline 9 V batteries (not included, suitable 18 V power supply: Art.333473)
• Dimensions (W x D x H): 162 x 102 x 44 mm
• Weight: 540 g

Connections:

• Input: 6.3 mm jack
• Tuner Out: 6.3 mm jack
• Drive out: 6.3 mm jack
• Deep Out: 6.3 mm jack
• Deep Out: XLR
• Drive Out: XLR
• Power supply connection: coaxial connector 5.5 x 2.1 mm (negative polarity inside)

• Character series
• Bass preamp pedal
• 3 Outputs: Amp / Recording output with Speaker Simulation / DI output
• 3-Band EQ
• Power supply via 9V battery or with power supply (not included) suitable power supply: e.g. 409939
• Dimensions: 12 x 14.5 x 6 cm
• Weight: 0.45 kg

The Tech21 programmable sansamp bass driver DI is far more than just a DI box. With the effective tone control and the ability to save 3 sounds and activate them with one stomp you will have a comfortable preamp in front of you. Whether into the amp or directly into the mixer - this device sounds like a large and expensive one!

• Storable version of the classic "bass driver DI"
• Optimised for live applications
• Three storable sounds
• Metal casing
• Power supply via 9V battery
• Optional AC adapter or via phantom power

The TECH-21 MIDI Mouse is quickly explained. A small Midi Switcher in pocket format. On the front, there is an up / down button, an Activ / Search button and a large LED display, which is also easy to read on the darkest stage. The destination preset can be selected without the active program is cut. Pressing the Active / Search button activates the new program. The Midi Mouse can either be powered by an external power supply, via phantom power via Midi cable or with a 9V battery. During battery operation the display goes into the "sleep" mode after some time the Midi Mouse has not been used, in order to avoid unnecessary battery runs. At the slightest pressing one of three buttons, the display is back on immediately.

• With up / down button
• Easy to use
• Battery operation also possible