Signal Splitters

Cranborne Audio N22; analog signal distributor via Cat5 cable; up to 100 m transmission range; 2 XLR inputs, 2 XLR or 2 trs jack outputs; 1 RJ45 input and 1 RJ45 output

• Phase reverse switch
• Galvanic isolation of the channels
• Ground lift switch
• Main Mic Input XLR
• Isolated mic input / merger XLR
• Mic Main Out XLR
• Isolated Mic Out / Splitter XLR

• Consists of eight balanced low-impedance microphone signals 16 microphone signals (8 pairs)
• Direct output and a transformer-isolated output in each channel
• Passing the phantom power to the main output
• Ground-lift switch for the separate output
• Switchable damping (PAD) in each input
• Format: 19"/ 1U

• From eight symmetrical microphone signals (low impedance) -> 16 microphone signals (8 pairs)
• Direct output and a galvanic isolated output per transformer on each channel
• Transit of phantom power to the main output
• Ground-lift switch for the isolated output
• Switchable attenuation (pads) on each input
• Format: 19" / 1U

PALMER Y-Box, splitbox for guitar signals. "When I am connecting the inputs of my two amplifiers, there is a strong hum." A frequent query in the technical section of relevant specialist magazines. The solution to this problem is the Palmer Y-Box. An FET input circuit converts the high-impedance guitar signal and, at the same time, forms the driver circuit for a transformer that directs the signal to the output ground-free. The hum loop is avoided. Operation with 9 V battery recommended.

The box can also be used as cable driver for large cable length. In addition, it is possible for the output AMP2 to phase-shift the signal. This is often necessary when two (pre)amplifiers are connected in parallel.

• Clinking input with 1 Mohm input impedance
• Output AMP1 as parallel circuit
• Output AMP2 is electronically converted with a subsequent transformer stage
• Operation with 9V battery recommended
• 5 years manufacturing guarantee

• 2 x 2 Identical sections with two balanced inputs and one balanced output each (4 x 2 in 1)
• Front side is switchable from 2 x 2 in 1 to 4 in 1 (output signal can then be split to both outputs)
• Rear side inputs balanced symmetrically via XLR
• Optimised for line level signals
• Impedance: 20 kOhm
• Differentiation of the input signals with the highest common mode rejection (CMMR)
• Internal filters for band limitating to a safe and useful range from 5-40 kHz (-1 dB)
• Multiturn trimpots on the front for level adjustment in the range of -12 up to 12 dB
• Balancing of the output signals with optimised circuits for highest resistance - and voltage common mode rejection ratio
• IRT compliant output impedance of 30 ohms
• XLR input and output sockets with gold-plated contacts

• Input: 1x XLR female
• Output: 3x XLR male
• Ground lift switch
• Implementation of 48 V phantom via the THRU Out
• Dimensions: 125 x 90 x 45 mm

Note: No 48V phantom power

• Press splitter 10 channel stereo / 20 channel mono
• 2 Channels
• Input level: +20 dB
• 2 XLR inputs
• Outputs: 6.3 mm jack, RCA, XLR, controls like attenuator
• Ground lift
• Input gain
• Mic / line switch
• Phones level, etc.
• Powder coated steel
• Internal shielded power supply
• Dimensions (W x D x H): 480 x 200 x 135 mm
• Weight: 9.09 kg

• Nominal impedance 600 ohms
• Max. input +20 dB
• 19" / 1U
• On the front of each channel: 1 Input + 1 thru (for phantom power transmission), 2x isolated outputs
• 5 Year warranty

• Jensen transmitter for high sound quality
• Connections: XLR in / thru / out
• Switchable 30 dB pad
• Switchable Gnd / Lift
• Robust metal housing
• Installation of up to 8 units is possible with the 2 U / 19" Radial J-Rack

• 2 x 1 in 4/4 x 1 in 2
• 2 x 2 Identical sections, each with one balanced input to two balanced outputs (4 x 1 in 2)
• Front switchable from 2 x 1 in 2 to 1 in 4
• Rear inputs balanced via XLR
• XLR input jacks with gold-plated contacts
• Optimised for line-level signals
• Impedance: 20 kOhm
• Differentiation of the input signals with highest common mode rejection
• Internal bandlimiting filter to a safe and reasonable range of 5 Hz -40 kHz (-1 dB)
• Front spindle trimmer for level adjustment in the range -12 to 12 dB
• Balancing of the output signals with optimised circuits for highest
• Resistance and voltage unbalance damping
• IRT compliant output impedance 30 ohms
• XLR output jacks with gold-plated contacts

• XLR inputs and outputs
• Design: 19"/1HE

• XLR / jack combo input
• 3 XLR outputs
• Switchable ground / lift per output
• Jensen transformer
• Frequency range: 20 - 20,000 Hz
• Dynamic range: 140 dB
• Robust metal housing
• Dimensions: 84 x 127 x 48 mm

• Passive
• Four stereo input channels
• Stereo output (all 6.3 mm jack connectors are stereo - tip, ring, sleeve)
• Dimensions: 47 x 117 x 104 mm
• Weight: 380 g

• 1 Input: XLR
• 2 Outputs: XLR
• 1 Thru: XLR
• Ground lift switchable per output
• Neutrik connectors
• Sturdy, compact aluminium housing with protective corners made of hard rubber
• Dimensions (W x H x D): 118 x 64 x 120 mm
• Weight: 0.6 kg
• Design and developed in the UK