ADDAC

• 4 Independent channels for controlling drum modules or envelopes
• Each channel converts gate signals into 1ms triggers
• Bypass switch per channel
• Current consumption: 10 mA (+12 V) / 10 mA (-12 V)
• Width: 3 HP
• Depth: 25 mm

• Four-voice percussion module
• Per channel T-network with frequency control and range switch (low / mid / high)
• Trigger input and audio output per channel
• Mix-out of all 4 channels with volume control
• Current consumption: 40 mA (+12 V) / 40 mA (-12 V)
• Width: 6 HP
• Depth: 25 mm

• 8 Buttons for manual generation of gate signals (+5 V)
• 4 of the 8 channels have signal inputs and can be used as momentary switches
• Current consumption: 10 mA (+12 V) / 10 mA (-12 V)
• Width: 8 HP
• Depth: 25 mm

• Aluminium case and wooden side panels with Wenge Veneer
• 7 rows / 21 U
• Width: 197 U per row (1379 U total)
• Available installation depth for modules: 6 - 12.5 cm
• 14 bus boards with 14 slots each for modules
• Active cooling with quiet 8 cm fan
• Built-in power supply
• Maximum current output: +12V / 20A, -12V / 20A
• Dimensions (W x H x D): 1040 x 850 x 460 mm
• Weight: 25 kg

• 4-Channel random generator
• Adjustable minimum / maximum values for voltage and time
• CV inputs for all parameters
• Chromatic quantisation switchable
• Normal or Brownian random distribution for voltage and time can be selected
• Switchable input for external clock
• Expandable with ADDAC 501B expander (article 505630)
• Power requirement: 120mA (+ 12V) / 20mA (-12V)
• Width: 8 HP
• Depth: 50mm

• 2-channel interface for looping in guitar effect pedals
• 2x send and return path in 3.5 mm and 6.3 mm jack socket
• Input and output amplifier designed for instrument signals
• Consumption: 10 mA (+12 V) / 10 mA (-12 V)
• Width: 4 TE
• Depth: 30 mm

ADDAC 710 Balanced Outputs; Eurorack module; dual-channel DI-module with output transformers; suitable for adapting Eurorack signals to line level without ground loops; for each channel: 3.5mm input jack, 3-way ground-lift switch (Lift, Float, Ground), clip LED and XLR output; power consumption: 40mA (+12V / 40mA (-12V); width: 6 HP; depth: 40mm

• 4-Channel square wave oscillator with FM and multimode filter
• Per channel: Trigger input, adjustable decay envelope, adjustable frequency and switchable FM through the previous oscillator.
• Multimode filter with settings for cutoff and resonance
• Cutoff CV input with bipolar attenuator
• Filter outputs for low-pass
• Bandpass and highpass
• Current consumption: 40 mA (+12 V) / 40 mA (-12 V)
• Width: 8 HP
• Depth: 45 mm

• Extension to the ADDAC 501 Complex Random (available under Article Nr 505630 (not included))
• Derives a positive and inverted gate signal from channels 1-3
• Smooth knob defines the amount of legato between each clock step
• Powered via ADDAC 501 module
• Width: 4 HP
• Depth: 50 mm

• Discrete analogue stereo mixer for audio signals
• Three stereo channels, each with gain and panorama controls
• One mono channel with gain control
• Produces sound colourations from slight compression to overdrive at higher levels
• Feedback control for subtle overdrive up to drastic gate effects
• Master volume control with signal LEDs and switchable soft clipping
• Stereo master output
• Current consumption: 80mA (+12V) / 80mA (-12V)
• Width: 8 TE
• Depth: 40 mm

• Real-time looper with overdub / punch-in recording and variable playback direction
• Save and load banks, presets and loops directly to SD card
• Max. 5 min. recording time per bank
• Max. 99 presets per bank and max. 99 loops per preset can be stored - format: mono .wav, 16 bit, 44.1 kHz
• Granular engine with real-time control over all parameters, e.g. number of grains, grain size, envelope shape, playback direction, pitch and more
• CV/trigger inputs for all granular parameters and for looper control
• 2 Mono audio inputs (Eurorack level) and 1 stereo line input (3.5mm jack)
• 3 Audio outputs: left, right, mono
• Power consumption: 240 mA (+12 V) / 70 mA (-12 V)
• Width: 32 HP (ADDAC 112A) + 13 HP (ADDAC 112B)
• Depth: 45 mm

• Mixer for audio and CV signals
• 2 Independent sections (A & B)
• 2 Signals per section can be mixed, inverted, and rectified
• Bipolar level control per input (X & Y)
• Bipolar amplitude and offset control per section output
• Per section 2 input (X & Y), master output and inverted output
• Averaged mix output from A & B

• Stereo Tilt Equaliser
• Spectral Tilt control for boosting treble while cutting bass or vice versa
• Tilt CV input with bipolar attenuator
• Spectral Motion switch allows synchronous or opposite spectral shifting of left and right channels
• Stereo input and output
• Current consumption: 40 mA (+12 V) / 40 mA (-12 V)
• Width: 4 HP
• Depth: 45 mm

ADDAC 311 Ultra Floor Control; Eurorack module with floor pedal; allows the use of up to 5 expression pedals and 5 foot switches to generate control voltages, gate and trigger signals; floor pedal with 5 inputs for expression pedals (TRS pinout); input 4 configurable for RTS pinout via jumper; input 5 configurable for TS pinout via jumper; for each expression pedal input: attenuverter (-5V to +5V), pedal mode selector and LED monitor; 5 footswitches, each with status LED, selectable polarity and mode switch (Gate, Trigger, Latch); Eurorack module with 10 outputs (x5 expression CV, x5 gate/trigger); connection between module and floor pedal via DB25 cable (length 3.0m, included); power consumption: 100mA (+12V) / 50mA (-12V); width: 6 HP; depth: 25mm; floor pedal dimensions (WxDxH): 320 x 150 x 60mm; floor pedal weight: 1kg

• CV and gate generator
• 4 Independent sine LFOs whose sum results in a complex modulation voltage (Relabi Wave)
• Top and bottom thresholds define threshold values to generate gate signals for outputs 1-4 from the LFO signals
• Gate length adjustable
• Frequency and amplitude per LFO adjustable
• CV input with bipolar attenuators for LFO 1, LFO 2, threshold and gate length
• Trigger input and manual trigger button
• 3 Selectable play modes (pause, reset and advance)
• LFOs 2-4 can be synchronised to LFO 1
• Current consumption: 100 mA (+12 V) 40 mA (-12 V)
• Width: 10 HP
• Depth: 40 mm

• 8 Illuminated switches for manual generation of a fixed voltage (+5 V)
• 4 of the 8 channels have signal inputs and can be used as latching switches
• Current consumption: 10 mA (+12 V) / 10 mA (-12 V)
• Width: 8 HP
• Depth: 25 mm

ADDAC 809 Chain Router; Eurorack module; CV controllable signal router; two signal-loops (A&B), each with input and output; 6 different routings selectable via buttons, gate inputs and Scroll CV input: Bypass, Loop A, Loop B, Loop A into Loop B, Loop B into Loop A, Loop A/B parallel; power consumption: 80mA (+12V) / 30mA (-12V); width: 6 HP; depth: 55mm