|
|
JHS Pedals Overdrive Preamp, overdrive effects pedal, faithful replication of the DOD Overdrive / Preamp (250) V1, powerful tone shaping tool, can be used as a solo boost, always on preamp, transparent overdrive or distortion, two switchable clipping arrangements (Down for a more distorted, saturated sound, Up for a more open, louder and clearer sound), true bypass, controls for Level, Gain, clipping arrangement slider switch, bypass footswitch, status LED, metal housing, 6.3 mm mono in / output jacks, power supply via optional 9-18V DC adapter 2.1 mm x 5.5 mm barrel plug, polarity (-) center, battery operation not supported, current draw 5 mA, dimensions (L x W x H) 119 x 94 x 42 mm / 4.7" x 3.7" x 1.66", weight ca. 450 g / 0.99 lbs, made in USA, Note: DOD and Overdrive / Preamp (250) are the trade names, trademarks or service marks of their respective owners
|
Price History: JHS Pedals Overdrive Preamp
178.00 $ |
|
|
Effect Pedal
- Phaser
- From the JHS Pedals 3 Series
- Intuitive control options offer a wide spectrum of possible sounds
- Six-stage phaser inspired by the classic phaser circuits of the 70s
- Feedback switch gives the effect resonance and creates more intense phasing by emphasising certain frequency ranges
- True bypass
- Controls for blend, rate, width
- Feedback toggle switch
- Bypass footswitch
- Status LED
- Input: 6.3 mm jack
- Output: 6.3 mm jack
- Power supply via 9 V DC mains adapter (not included in delivery) with 5.5 x 2.1 mm barrel connector, negative polarity inside
- Current consumption: 71 mA
- Metal housing
- Dimensions (L x W x H): 112 x 60 x 31 mm
- Weight: approx. 210 g
Note: Battery operation is not supported. Note: Register your product at www.w-distribution.de/Warranty and extend the warranty to 4 years.
|
Price History: JHS Pedals 3 Series Phaser
111.00 $ |
|
|
Effect pedal for electric guitar
- Fuzz
- Legendary Direct-In Fuzz sounds
- Distortion Section of the JHS colour box
- True bypass
- Controller for Master, Pre and Tilt
- Toggle switch for activating the hi-pass filter
- Bypass footswitch
- Status LED
- Metal housing
- Input and output: 6.3 mm mono jack
- Powered by optional 9V DC power adapter (not included), 2.1mm x 5.5mm barrel plug, polarity (-) inside
- Current consumption: less than 100 mA
- Dimensions (L x W x H) 130 x 70 x 60 mm
- Weight: 260 g
- Made in USA
Note: No battery operation possible.
|
Price History: JHS Pedals Crayon
195.00 $ |
|
|
Effect Pedal
- Flanger
- From the JHS Pedals 3 Series
- Intuitive controls offer a wide range of possible sounds
- Tape switch creates tape-like sweeps
- True bypass
- Controls for blend, rate, intensity
- Tape toggle switch
- Bypass footswitch
- Status LED
- Input: 6.3 mm jack
- Output: 6.3 mm jack
- Power supply via 9 V DC mains adapter (not included in delivery) with 5.5 x 2.1 mm barrel connector, negative polarity inside
- Power consumption: 70 mA
- Metal housing
- Dimensions (L x W x H): 112 x 60 x 31 mm
- Weight: approx. 210 g
Note: Battery operation is not supported.Note Register your product at www.w-distribution.de/Warranty and extend the warranty to 4 years.
|
Price History: JHS Pedals 3 Series Flanger
111.00 $ |
|
|
Effect Pedal for Electric Guitar
- Reverb
- Real amp-style spring reverb tones
- 2 Reverb mix controls
- Boost, Highs, Length, Depth, Tank 1 and Tank 2 controls
- Bypass footswitch
- Tank 2-foot switch
- Status LEDs
- Metal housing
- Input / output: 6.3 mm mono jack
- TRS effect grinding path 6.3 mm
- Power supply via optional 9 V DC power supply (not included), 2.1 mm x 5.5 mm barrel connector, polarity (-) inside (battery operation not supported)
- Power consumption less than 100 mA
- Dimensions (L x W x H) 130 x 70 x 60 mm
- Weight 260 g
- Made in USA
|
Price History: JHS Pedals Spring Tank
178.00 $ |
|
|
Effects Pedal
- From the 'Legends Of Fuzz' series by JHS Pedals
- Based on the early silicon fuzz faces from Arbiter Electronics
- Aggressive, biting sounds with a nice vintage character
- Switchable JHS mode puts the pedal in high-gain / gated fuzz range
- True bypass
- Volume and fuzz controls
- Mode switch
- Bypass footswitch
- Status LED
- 6.3 mm Mono jack input / output
- Power supply with 9 V battery or via 9 V DC power supply (2.1 mm x 5.5 mm coaxial connector, polarity (-) inside, not included)
- Current consumption less than 100 mA
- Metal housing
- Dimensions (L x W x H): 144 x 92 x 51 mm
- Weight: approx. 380 g
Note: Register your product at https://shop.warwick.de/en/warrantyregistration and extend the guarantee to 4 years.
|
Price History: JHS Pedals Smiley - Fuzz
175.00 $ |
|
|
Effect Pedal for Electric Guitar
- Overdrive
- Controls for Volume, Drive, Tone
- 2-Way switch for different Overdrive presets
- True Bypass
- Power supply via 9 V power supply unit (not included in delivery, suitable power supply unit available: Article 409939)
- Made in USA
Note: No battery operation possible
|
Price History: JHS Pedals SuperBolt V2
205.00 $ |
|
|
Effects Pedal for Electric Guitar
- Distortion
- From the JHS Pedals 3 Series
- Intuitive control options offer a wide range of possible sounds
- Ranges from rich medium-gain crunch to classic overdrive and distortion sounds to fuzz-like distortion
- Gain switch selects between two gain options
- True bypass
- Controls for Volume, Filter, Distort
- Gain toggle switch
- Bypass footswitch
- Status LED
- Metal housing
- Input: 6.3 mm jack
- Output: 6.3 mm jack
- Power supply via 9 V DC power adapter (2.1 mm x 5.5 mm barrel connector, polarity (-) inside, not included)
- Current consumption: 9 mA
- Dimensions (L x W x H): 112 x 60 x 31 mm
- Weight: approx. 210 g
- Made in the USA
Note: Battery operation is not supported. Note: Register your product at https://shop.warwick.de/en/warrantyregistration to extend the warranty to 4 years.
|
Price History: JHS Pedals 3 Series Distortion
108.00 $ |
|
|
Effect Pedal for Electric Guitar
- Overdrive
- From the JHS Pedals 3 Series
- Based on the modifications and work with the legendary TS circuitry
- TS 'Strong Mod' in a stand-alone unit
- More clean headroom
- Better usability as boost
- More versatile drive and tone controls and a more 'pleasing' frequency response than standard TS-style pedals
- Two switchable clipping modes (Up (+) for asymmetrical clipping (JHS 'Strong Mod' clipping), Down (-) for symmetrical clipping (standard TS9 / TS808 style))
- True Bypass
- Volume, Tone, Drive controls
- +/- Toggle switch
- Bypass footswitch
- Status LED
- Metal housing
- 6.3 mm mono jack input / output
- Power supply via 9V DC mains adapter (2.1 mm x 5.5 mm hollow female plug, polarity (-) inside - not included)
- Battery operation is not supported
- Power consumption: 12 mA
- Dimensions (L x W x H): 112 x 60 x 31 mm
- Weight: approx. 210 g
Note: Register your product at www.w-distribution.de/Warranty and extend the warranty to 4 years
|
Price History: JHS Pedals 3 Series Screamer - Overdrive
111.00 $ |
|
|
Switch pedal
- A/B/Y Switcher / Splitter
- Active working method
- Output transformer eliminates hum - no ground lift necessary
- FET transistors for silent switching
- AB foot-switch
- Y foot-switch
- Status LEDs
- Metal casing
- 6.3 mm Mono jack inputs
- 2x 6.3 mm Mono jack output
- Power supply via 9 V power supply unit (2.1 mm x 5.5 mm hollow plug, polarity (-) inside, not included in delivery)
- Power consumption of less than 100 mA
- Dimensions (W x D x H): 115 x 65 x 51 mm
- Weight: 300 g
- Made in USA
Note: Battery operation is not supported. Note: Register your product at www.w-distribution.de/Warranty and extend the warranty to 4 years.
|
Price History: JHS Pedals Active A/B/Y
133.00 $ |
|
|
Switch pedal
- A/B/Y Switcher / Splitter
- Active working method
- Output transformer eliminates hum - no ground lift necessary
- FET transistors for silent switching
- AB foot-switch
- Y foot-switch
- Status LEDs
- Metal casing
- 6.3 mm Mono jack inputs
- 2x 6.3 mm Mono jack output
- Power supply via 9 V power supply unit (2.1 mm x 5.5 mm hollow plug, polarity (-) inside, not included in delivery)
- Power consumption of less than 100 mA
- Dimensions (W x D x H): 115 x 65 x 51 mm
- Weight: 300 g
- Made in USA
Note: Battery operation is not supported. Note: Register your product at www.w-distribution.de/Warranty and extend the warranty to 4 years.
|
Price History: JHS Pedals Active A/B/Y Switch
133.00 $ |
|
|
Effect Pedal for Electric Guitar
- Overdrive
- Controls for volume, drive, tone and gain switch
- Gain switch activates a boost mode for more low-end and higher distortion
- Additional footswitch connector for gain switch
- True bypass
- Very transparent tone
- TRS inputs and output
- Operates exclusively on power supply (not included, matching power supply available under Art. Nr 409939)
- Hand built in the USA
|
Price History: JHS Pedals Morning Glory V4
205.00 $ |
|
|
Effects Pedal for Electric Guitar
- Overdrive
- From the JHS Pedals 3 Series
- Intuitive control options offer a wide range of possible sounds
- Ranges from colour boost through transparent low-gain drive to rich, natural medium-gain overdrive
- Gain switch selects between two gain options
- True bypass
- Controls for Volume, Body, Drive
- Gain toggle switch
- Bypass footswitch
- Status LED
- Metal housing
- Input: 6.3 mm jack
- Output: 6.3 mm jack
- Power supply via 9 V DC power adapter (2.1 mm x 5.5 mm barrel connector, polarity (-) inside, not included)
- Current consumption: 12 mA
- Dimensions (L x W x H): 112 x 60 x 31 mm
- Weight: approx. 210 g
- Made in the USA
Note: Battery operation is not supported. Note: Register your product at https://shop.warwick.de/en/warrantyregistration to extend the warranty to 4 years.
|
Price History: JHS Pedals 3 Series Overdrive
111.00 $ |
|
|
Effect pedal for electric guitar
- Fuzz distortion
- Reproduction of the Lovetone Big Cheese
- Analog operation
- True bypass
- Volume, Gain and Tone controls
- 4-Way switch for selecting four gain and tone settings
- Bypass foot-switch
- Status LED
- Metal casing
- Input and output: 6.3 mm mono jack
- Power supply via 9 V DC power supply, 2.1 mm x 5.5 mm hollow plug, polarity (-) inside (not included in delivery)
- Current consumption: below 100 mA
- Dimensions (L x W x H): 121 x 56 x 41 mm
- Weight: 260 g
- Made in USA
Note: Battery operation not supported. Note: Register your product at https://shop.warwick.de/en/warrantyregistration and extend the warranty to 4 years.
|
Price History: JHS Pedals Cheese Ball - Fuzz Distortion
178.00 $ |
|
|
Effects Pedal for Electric Guitar
- Compressor
- From the JHS Pedals 3 Series
- Intuitive control options offer a wide range of possible sounds
- Ranges from smooth smoothing to extremely compressed sounds
- Bright switch activates a brighter EQ voicing
- True bypass
- Volume, attack, and sustain controls
- Bright toggle switch
- Bypass foot switch
- Status LED
- Metal housing
- Input: 6.3 mm jack
- Output: 6.3 mm jack
- Power supply via 9 V DC power supply (2.1 mm x 5.5 mm barrel connector, polarity (-) inside, not included)
- Current consumption: 8 mA
- Dimensions (L x W x H): 112 x 60 x 31 mm
- Weight: approx. 210 g
- Made in the USA
Note: Battery operation is not supported. Note: Register your product at https://shop.warwick.de/en/warrantyregistration and extend the guarantee to 4 years.
|
Price History: JHS Pedals 3 Series Compressor
111.00 $ |
|
|
Parametric Mid-EQ Effect Pedal
- Analogue operation
- Up to +/- 15 dB Mid Boost or Cut
- Center frequency adjustable from 400 Hz to 7.5 kHz
- Switchable Q setting (LO / HI)
- True bypass
- Controls for Volume, Mids and Sweep
- Lo / Hi toggle switch to select the Q-setting
- Bypass footswitch
- Status LED
- Metal housing
- 6.3 mm Mono IN / OUT jacks
- Power supply via optional 9V DC adapter with 2.1 x 5.5mm barrel connector and polarity: (-) inside (power supply not included)
- Power consumption: Less than 100 mA
- Dimensions: 66 x 122 x 40 mm
- Weight: 290 g
Note: Register your product at www.w-distribution.com/Warranty and extend the warranty to 4 years.
|
Price History: JHS Pedals Haunting Mids - Parametric EQ
151.00 $ |
|
|
Effect Pedal
- Reverb / Hall
- From the JHS Pedals 3 Series
- Intuitive control options offer a wide spectrum of possible sounds
- Inspired by the sounds of great halls, cathedrals and halls
- Modulate switch activates the modulation of the reverb decay for a slightly detuned effect and a three-dimensional sound feeling
- True Bypass
- Controls for verb, dampen, decay
- Modulate toggle switch
- Bypass footswitch
- Status LED
- Input: 6.3 mm jack
- Output: 6.3 mm jack
- Power supply via 9 V DC mains adapter (not included in delivery) with 5.5 x 2.1 mm barrel connector, negative polarity inside
- Current consumption: 8 mA
- Metal housing
- Dimensions (L x W x H): 112 x 60 x 31 mm
- Weight: approx. 210 g
Note: Battery operation is not supported. Note: Register your product at www.w-distribution.de/Warranty and extend the warranty to 4 years.
|
Price History: JHS Pedals 3 Series Hall Reverb
111.00 $ |
|
|
Effects Pedal for Electric Guitar
- Delay
- From the JHS Pedals 3 Series
- Intuitive control options offer a wide range of possible sounds
- Adjustable delay time from 80 ms to 800 ms
- Ranges from short slapbacks to long ambient echoes
- Type switch selects between two voicing modes (digital-voiced / analog-voiced)
- True bypass
- Controls for mix, time, repeats
- Type toggle switch
- Bypass foot switch
- Status LED
- Metal housing
- Input: 6.3 mm jack
- Output: 6.3 mm jack
- Power supply via 9 V DC power supply (2.1 mm x 5.5 mm barrel connector, polarity (-) inside, not included)
- Current consumption: 71 mA
- Dimensions (L x W x H): 112 x 60 x 31 mm
- Weight: approx. 210 g
- Made in the USA
Note: Battery operation is not supported. Note: Register your product at https://shop.warwick.de/en/warrantyregistration and extend the guarantee to 4 years.
|
Price History: JHS Pedals 3 Series Delay
111.00 $ |
|
|
Effect Pedal
- Multi-mode overdrive / distortion / fuzz
- Combines 9 selectable Proco RAT sound modes in one pedal: OG V1, White Face V3, Turbo V5, BRAT V6, Dirty V7, LA, Landgraff MO'D, Caroline, JHS Mode
- Unique switching system combines fully analogue switching with digital control for each mode
- Extremely accurate replication of the individual models
- True bypass
- Controls for volume, distortion, filter
- 9-Way selector switch for sound mode
- Bypass footswitch
- Status LED
- Input: 6.3 mm jack
- Output: 6.3 mm jack
- Mains adapter connection: Hollow female plug 5.5 x 2.1 mm, negative polarity inside
- Power supply via 9 V DC mains adapter (not included in the delivery)
- Current consumption is less than 100 mA
- Metal housing
- Dimensions (L x W x H): 121 x 66 x 40 mm
- Weight: approx. 350 g
- Made in USA
Note Register your product at www.w-distribution.de/Warranty and extend the warranty to 4 years.
|
Price History: JHS Pedals Packrat
239.00 $ |
|
|
Switch
- A / B dial footswitch
- Passive way of working
- Two-colour status LED
- Metal housing
- Input and output: 6.3 mm mono
- Powered by optional 9V DC power adapter (not included), 2.1mm x 5.5 mm hollow plug, polarity (-) inside
- Power consumption: less than 100 mA
- Power supply only required for the status LED
- Dimensions (L x W x H) 95 x 47 x 35 mm
- Weight 140 g
- Made in USA
Note: no battery operation possible
|
Price History: JHS Pedals Mini A/B Box
62.00 $ |