Lehle

• With loop for one instrument on up to three amps
• The Lehle 1at3 routes the input signal as a true true bypass switcher via gold-plated relays to up to three outputs (eg. amps, tuners, effects)
• If the input signal is only present on one of the outputs, then the ground connections are connected - ground loops are thereby excluded
• The output C and the socket C-> B can also be used as a loop
• Enabling you to switch to and fro between the pure original signal and the effects loop
• The Lehle 1at3 can be controlled via MIDI and networked with other Lehle SGoS switches
• Power supply available as an option

• Allows switching between different instruments in stereo via gold-plated contact relays
• Without semiconductors, the signal from inputs A, B or C pass through outputs 1 or 2 unaltered. This makes it easy to switch between an amp and a tuner
• Can be controlled via MIDI and networked with other Lehle SGoS switches
• True bypass
• LED: Effects On
• Footswitch: Effects bypass
• Input: 6.3 mm jack
• Output: 6.3 mm jack
• Power supply port (coaxial socket, 5.5 x 2.1 mm - negative polarity inside)
• Power consumption: 97 mA
• Powered via 8-20 V DC power supply (not included, suitable power supply available under Article Nr 409939 (not included))
• Dimensions (W x D x H): 156 x 103 x 47 mm
• Weight: 735 g
• Made in Germany

Note: Battery operation is not supported.

Lehle P-Split III; Splitter, DI box and problem solver; high-impedance Lehle Transformer HZ with phase and ground switch; can be used unbalanced or balanced; passive - does not require a power supply, Applications: Split an input signal to the two outputs with galvanic isolation (no ground loop); elimination of unwanted humming noise; passive Mono Summer for stereo signals; Connections: Input (1/4" TRS-Jack), DIR Output (1/4" TRS-Jack), ISO Output (1/4" TRS-Jack); Dimensions (W x D x H): 92 x 90 x 37 mm (3,62" x 3,54" x 1,46"); Weight: 375 g (0,83 lbs)

• For two amps plus tuner with high impedance LTHZ transformer and gain reduction
• The Lehle Dual switches the signal via gold-plated relays to outputs A, B or T
• Outputs A and B can be operated at the same time on two different amps, since A to B is galvanically isolated by the high-end transformer Lehle LTHZ - ground loops are thereby excluded
• With the potentiometers, the outputs A and B can be attenuated separately
• The output T is available for a tuner or a third amp
• The two inputs can be stereo-routed to outputs A and B.
• In addition, the Lehle Dual has a gold-plated phase reversal and a ground switch
• The Lehle Dual can be controlled via MIDI and networked with other Lehle SGoS switches
• Power supply available as an option

• ABY-Switcher (A or B or both)
• Hum- and loss-free switching
• High-impedance Lehle Transformer HZ
• With phase and ground switch
• Two different operating modes
• Stereo routing options
• Active switching click suppression
• Push-buttons: TRS Switch, Phase, Ground
• LED: A, B
• Foot-switch: A, B
• A/B input: 6.3 mm Stereo jack
• A Input: 6.3 mm Jack
• A Output: 6.3 mm Jack
• B Output: 6.3 mm Jack
• Mains adapter connection: Hollow plug socket 5.5 x
• 2.1 mm, minus pole inside
• Current consumption: 63 mA
• Power supply via 9-15 V DC power supply unit (not included in delivery, suitable power supply unit: Article Nr. 409939)
• Dimensions (W x D x H): 122 x 99 x 47 mm
• Weight: 540 g

Note: Battery operation is not supported.

• With two independent, true True Bypass loops and switchable High End Bufferamp
• The Lehle D.Loop is a fully programmable effect looper / switcher with two independent true bypass loops via gold-plated relays
• It also has a switchable High End Bufferamp with adjustable gain up to +12 dB
• Loops and buffer amp are fully stereo
• The Lehle D.Loop can be controlled via MIDI and networked with other Lehle SGoS switches
• Power supply available as an option

• Equipped with a precision magnetic sensor
• Doesn't include a mechanical potentiometer
• Controls the volume on two channels with a volume range from -92 dB (virtually muted) to 0 dB (unity gain)
• No damping of higher frequencies
• No sound loss
• The supply voltage is rectified, filtered, stabilised, and doubled to 18V
• Both outputs can be tapped balanced and unbalanced
• Total dynamic range of 110 dB with a Blackmer Stereo VCA
• Low-friction bearings
• Brake can be finely adjusted
• Summing function: Two separate input signals can be summed to one output channel
• Split function: Mono signal can be output as dual mono
• Power supply via a 9V - 15V DC or oder 7 - 12 V AC (coaxial power connector - polarity is not relevant, corresponding power suppy available under Article Nr 409939 (not included, must be ordered separately)

• Operates wear-free via a precision magnetic sensor
• Without a mechanical potentiometer
• Volume from -92 dB (mute) to 0 dB (unity gain), or +12 dB (boost with adjustable potentiometer)
• No damping of higher frequencies
• No sound loss
• Supply voltage is rectified, filtered, stabilized and doubled to 18V
• Total dynamic range of 110 dB by use of a Blackmer VCA
• Low-friction bearings
• Finely adjustable brake
• Buffered direct-out as an output for a tuner or second amp
• Power supply via a 9V - 15V DC or oder 7 - 12 V AC (coaxial power connector - polarity is not relevant, corresponding power suppy available under Article Nr 409939 (not included, must be ordered separately)

• 2 Outputs
• Active, wear-free expression pedal equipped with a precise magnetic sensor
• 2 Digital potentiometers with analogue voltages for the precise and reliable generation of expression data
• Both outputs can be used with almost all common devices with expression inputs from 5k to 100k , including TS, TRS and/or RTS
• Polarity can be switched and stored via soft-push buttons
• The 10k output can be set as a latching- or momentary switch
• Via a USB jack you can send MIDI data to a computer for the control of MIDI-compatible software
• Resistance value of the potentiometer: 5-100 kOhm
• Button: Polarity
• LED: Polarity
• Connections: 2x 6.3 mm stereo jack
• Dimensions (W x D x H): 90 x 200 x 47 mm
• Weight: 766 g
• Made in Germany

• Inputs and outputs are located on the side
• Ideal for pedal steel players
• Equipped with a precision magnetic sensor
• Doesn't include a mechanical potentiometer
• Volume from -92 dB (mute) to 0 dB (unity gain), or +12 dB (boost adjustable with potentiometer)
• No damping of higher frequencies
• No sound loss
• With the help of the MIN knob, the minimum volume can be set from 0-90%
• Supply voltage is rectified, filtered, stabilised and doubled to 18V
• Total dynamic range of 110 dB with a Blackmer VCA
• Low-friction bearings
• Brake can be finely adjusted
• Buffered direct-out as an output for a tuner or a second amp
• Power supply via a 9V - 15V DC or oder 7 - 12 V AC (coaxial power connector - polarity is not relevant, corresponding power suppy available under Article Nr 409939 (not included, must be ordered separately)

• Applications: Take effect pedals out of the signal path without further ado, and pick up a signal at any point in the signal chain, e.g. to switch to a tuner or as a switch between two instruments to an amp or vice versa from an instrument between two amps.
• Not only the signal, but also the signal ground is switched to avoid hum loops.
• All jack sockets are stereo; symmetrical signals can also be transmitted
• Mono and stereo signals can be combined
• Three different operating modes: switch (latching), button (momentary) or mixed mode
• Foot-switch: Loop On Off/Output
• Input: 6.3 mm Stereo jack
• Output: 6.3 mm Stereo jack
• FX Send / Return: 2 x 6.3 mm Stereo jack
• Mains adapter connection: Hollow plug socket 5.5 x 2.1 mm, minus pole inside
• Current consumption: 70 mA
• Power supply via 9-15 V DC power supply unit (not included in delivery, suitable power supply unit: Article Nr. 409939)
• Dimensions (W x D x H): 90 x 96 x 47 mm
• Weight: 350 g
• Made in Germany

Note: Battery operation is not supported.

• Compact format with 50% less weight and 35% less size compared to the Lehle Mono Volume Pedal
• Wear-free due to precision magnetic sensor
• Without mechanical potentiometer
• 120 dB dynamic range thanks to 30 V technology
• No treble attenuation
• Up to +12 dB boost
• No sound loss
• Supply voltage is rectified, filtered, stabilised and doubled to 30 volts
• MIDI via USB
• Additional buffered direct output for a tuner, recording or a second amplifier without sound loss
• Low-friction slide bearing
• Power supply with a 9-15V mains adapter (5.5 x 2.1 mm hollow female plug socket - any polarity)
• Suitable power supply: art. 409939 (power supply not included)

• Networks up to four Lehle Lehle SGoS switches via standard stereo jack adapters, whereas the communication between the individual switches takes place via the MIDI programme change commands
• A five-pole DIN socket allows the external MIDI equipment to be connected, in response to the MIDI programme change commands
• The combination of several MIDI junction units allows the networking of up to ten Lehle SGoS switches
• Dimensions (W x D x H): 105 x 36 x 31 mm
• Weight: 179 g
• Made in Germany

• No signal loss or hum
• High-impedance Lehle transformer HZ
• Suitable for balanced or unbalanced signals
• Passive, no power supply required
• Galvanic isolation of units to avoid hum loops also for use as re-amping unit or as high-quality, compact DI box for all types of signals
• Input: 6.3 mm stereo jack
• Output: 6.3 mm stereo jack
• Dimensions (W x D x H): 72 x 41 x 31 mm
• Weight: 314 g
• Made in Germany