Oscillator Modules

• Dual VCO
• Dual Oscillator inspired by the Buchla Modular Synthesizer
• An analogue signal path available
• Screwed potentiometers
• Sine, sawtooth and square wave inputs and outputs as well as noise output
• CV inputs
• Soft and hard sync inputs
• Dimensions: 30 HP/TP width, up to 26 mm depth
• Colour: Black

The A-112 Module is a combined module of a voltage-controlled 8-bit sampler and a wavetable oscillator. Moreover, it is able to produce effects. It is available as a supplemental sound generator module for the A-100 with the characteristic sound characteristics of the early 8.Bit samplers and cannot be compared with commercially available MIDI samplers!

"Sampling mode: "

8-Bit audio resolution , 128 kB memory in 2 banks (S1, S2) of 64KB each (this corresponds to 2 seconds sampling time at 32 kHz sampling frequency), audio input with attenuator, overdrive display in recording mode (gate LED) Dump capability to archive sounds, non-volatile memory for the samples in the module, manual tune control to adjust the sampling rate during recording and playback, the CV input (1V / octave), along with the tune control The sampling rate or pitch (pitch 5 octaves corresponding to 0 ... 5V, pitch resolution 1/4 semitone), gate input (no pure trigger, but the sample is started at the positive edge and runs until the Gate input becomes "high" or the end of the sample is reached), manual gate button, unfiltered audio output (ie, quantisation sounds can be used for sound generation).

Wavetable mode:

A special form of sampling mode, with the audio input acting as a control input for the sample which is stored in one of two banks (S1, S2) with 64 kbyte of memory each. In wavetable mode each bank is arranged as 256 pages of 256 bytes. The wavetables are loaded in the sampling memory (normally loaded via MIDI dump), thus making a wavetable oscillator, in which different waveforms (with different harmonic content) are traversed by CV2. With this mode of operation, however, a "normal" sample can "pass through", which sometimes results in quite astonishing sounds (interesting for the "passing through" speech, where the language spins very extreme sound structures).

Effects:

In addition, the module offers - as a free "extra" so to speak - some effects such as delay, reverse delay, pitch shifter and freeze. It should be stressed, however, that these effects can not be compared with the result of high-quality effectors due to the 8-bit resolution and should only be understood as a free-of-charge addition for bizarre sounds.

• Combined module of voltage-controlled 8-bit sampler and wavetable oscillator
• Width: 10 HP / 50.5 mm
• Depth: 100 mm (measured from the back of the front panel)
• Power Requirements: 50mA (12V) / -20mA (-12V)

Thru Zero Quadrature - VCO oscillator generates sine and cosine waveforms at the same time. These are terminated as soon as the linear control voltage reaches 0V.

• Special Edition with additional output amplifier
• 2 Control sections: Linear and exponential
• Controller for XTune, XFM, LFrq and LFM
• Width: 8HP / 40.3 mm
• Depth: 60 mm
• Power requirements: 90mA
• Colour: Blue anodised front plate and white knobs

• Analogue through-zero oscillator
• Precise 1 volt/octave tracking over the entire audio range
• Exponential FM input with attenuator
• Linear through-zero FM input with attenuator, bias switch and AC-coupling switch
• Through-zero phase modulation with up to 900° offset
• Through-zero amplitude modulation for fundamental, odd and even outputs
• Hard-Sync (Reset) and Soft-Sync (Flip)
• (Flip) available in parallel
• Switchable LFO mode
• 5 Separate signal outputs: Core (triangle), Fundamental (sine), Even (sawtooth), Odd and Full-Mix
• Current consumption: 130 mA (+12 V) / 115 mA (-12 V)
• Width: 12 HP
• Depth: 30 mm

• Analogue VCO/LFO on CEM3340 basis
• Octave selector switch (control range: 8 octaves) and Fine-Tune control
• Selector switch for VCO and LFO mode
• Selector switch for linear or exponential FM
• CV inputs for FM and pulse width with attenuators
• Hard sync input
• Waveform outputs for: Sine, triangle, sawtooth, pulse, two complex waveforms and two square sub-octaves (-1 octave and -2 octaves)
• Current consumption: 50mA (+12V) / 30mA (-12V)
• Width: 8 HP
• Depth: 30 mm

• Thru Zero Complex Oscillator
• VCO 1 & 2 each with an octave switch
• Controls available for coarse- and fine-tuning, attenuators for Thru Zero FM and exponential FM
• Lowpass filter, wavefolder, phase modulation and shape
• Adjustable FM index with a CV input and a switchable VCO sync (soft and hard sync selectable per each VCO)
• Per oscillator CV inputs for pitch, sync, FM x 2, shape, phase position and intensity of phase modulation, wavefolder and filter
• 4 Waveform outputs per oscillator
• Current consumption: 200 mA (+12 V) / 180 mA (-12 V)
• Width: 26 TE
• Depth: 26 mm

• Vintage Edition with black front panel
• Voltage controlled oscillator
• 3-Position toggle switch
• Linear FM input and soft-sync input
• Tune control range can be set between approx. 1/2 octave and 4 octaves via a jumper
• Width: 8 HP / 40.3 mm
• Depth: 50 mm (measured from the rear of the front panel)
• Power requirements: + 12V: 150 mA (warm up period about 30 seconds), 60 mA (continuous operation) -12V: 30mA

• High-End VCO II / VCLFO
• Precise tracking over 10 octaves
• Wide frequency range: 0.5 Hz - 20 kHz in VCO mode, 0.001 Hz - 40 Hz in LFO mode
• Selector switch for LFO or VCO mode
• CV inputs with attenuators for exponential and linear FM and PWM
• Pulse width can be set
• Inputs for soft and hard sync
• Outputs available for sawtooth, square/pulse, triangle and sine wave
• Current consumption: 70 mA (+12 V) / 50 mA (-12 V)
• Black front panel
• Width: 14 TE
• Depth: 55 mm

• Switchable between LFO and VCO modes
• The range of the Tune control can be changed by jumper - position 1: 16 Hz to 20 kHz, position 2: 16 Hz to 70 Hz, without jumper: 16 Hz to 22 Hz
• Width: 4 HP
• Depth: 65 mm
• Power requirements: +40 mA (+12 V) / -40 mA (-12 V)

The oscillator generates sine and cosine waveforms at the same time. These are terminated as soon as the linear control voltage reaches 0 V.

• 2 Control sections: Linear and exponential
• Controller for XTune, XFM, LFrq and LFM
• Width: 8HP / 40.3 mm
• Depth: 60 mm
• Power requirements: 90 mA

• Quad wavetable modulator
• 4-Channel LFO and bass oscillator
• Channels: A & B with controls for frequency, amplitude and waveform selection.
• Channels C & D programmable via menu
• Assignable CV input for all channels
• Tap tempo
• Synchronisation of all channels possible
• Internal modulation matrix
• 1-Shot and Gated mode
• Sample & Hold and Track & Hold
• OLED display
• Own waveforms can be imported via MicroSD card
• Preset manager with 8 memory locations
• Preset morphing and CV control
• Outputs for each channel (A, B, C, D)
• Width: 12 HP

• Analogue Dual Oscillator
• Two independent oscillators, each with controls for coarse and fine tuning (5Hz - 20kHz), waveshape, FM attenuator and bipolar CV attenuator
• Upper oscillator with waveshaping from sine to sawtooth
• Lower oscillator with waveshaping from sine to square
• Pitch CV input (1V/oct.) and two audio outputs per oscillator
• Current consumption: 70mA (+12V) / 40mA (-12V)
• Width: 18 TE
• Depth: 45 mm

Behringer 2600-VCO; Eurorack module; analog VCO; frequency range: 10Hz - 10kHz and 0.03Hz - 30Hz in LF Mode; adjustable pulsewidth; CV input with attenuator for pulsewidth modulation; 3 FM inputs, each with attenuator; Keboard CV input (1V/oct.); outputs for triangle, sawtooth, sine and pulse waveforms; power consumption: 140mA (+12V) / 5mA (-12V); width: 16 HP; depth: 42mm

• Analogue VCO for complex waveforms
• Triangle-core oscillator with pitch control and octave selector switch
• Two ripple elements, based on synthesis of formant sounds (FOF)
• Ratio, warp, damping and waveform (sine/rectangle) are adjustable per ripple element
• Element mix control with CV input
• Adjustable mix of sine fundamental tone and ripple elements (with CV input)
• CV inputs for all parameters
• Pitch CV input (1V/oct.)
• CV inputs with attenuators for Pitch FM and Global FM
• Outputs for the main signal, fundamental tone, ripple elements A&B, impulses A&B (decay curve of the elements)
• Current consumption: 90mA (+12V) / 80mA (-12V)
• Width: 24 TE
• Depth: 30 mm

• 4-Channel square wave oscillator with FM and multimode filter
• Per channel: Trigger input, adjustable decay envelope, adjustable frequency and switchable FM through the previous oscillator.
• Multimode filter with settings for cutoff and resonance
• Cutoff CV input with bipolar attenuator
• Filter outputs for low-pass
• Bandpass and highpass
• Current consumption: 40 mA (+12 V) / 40 mA (-12 V)
• Width: 8 HP
• Depth: 45 mm

• Quadrature sine oscillator with filter and waveshaper
• SPIN section: Quadrature sine wave oscillator with 4 outputs (0°, 90°, 180°, 270°) and tracking over 4 octaves
• GRIND section: Compares the SPIN outputs with an input signal and derives square wave signals which are fed into a VCA and modulated by the 4 GRIND CV inputs and GRIND fader
• Depending on the setting, the module functions as an oscillator or state variable filter
• Controls for coarse and fine tuning, attenuation, GRIND/SPIN ratio
• FM input with attenuator (linear or exponential)
• GRIND input with attenuator
• 4 SPIN outputs provide phase-shifted sinusoidal signals or in filter mode low-pass, band-pass, high-pass and notch characteristics
• Current consumption: 81 mA (+12 V) / 78 mA (-12 V)
• Width: 18 TE
• Depth: 25 mm
• Colour: Black

• In addition, triangle, rectangle and sawtooth are available as waveforms
• Versatile manipulation of the spectrum with Harmonic Scan and Spectral Tilt
• Extensive control options and signal taps
• Current consumption: 120 mA, 90 mA (+12 / -12)
• Dimensions: 32 TE

Befaco Pony VCO 1U; compact analog Thru-Zero VCO with build-in Wavefolder and VCA; manual control for VCO frequency with range switch (Full, Octave, Semitone, LFO); octave selector; Timbre control for wavefolder intensity; four selectable waveforms: sine, triangle, sawtooth and square wave; CV inputs for pitch (1V/oct.), FM, Timbre and VCA; Sync input; VCO output; power consumption: 32mA (+12V) / 25mA (-12V); width: 24 HP; depth: 30mm