Neumann

• Universal use
• Self-adhesive
• Anti-slip material (cell rubber EPDM 60)
• Rounded edges
• Possible areas of application: under Monitor speakers, 19 "- or hi-fi equipment, table Cases and more.
• Dimensions per pad: 70 x 70 x 15 mm
• Colour: Black
• Set includes 4 pads

• For Neumann KH810 Subwoofer
• For controlling system-level
• Mute and bass management bypass
• Connectors: Neutrik RJ45 socket EtherCon
• Level control range: -95 - 20 dB
• Switching function: Bass Management (Enabled / Disabled)
• LFE Gain (0/10 dB)
• Display: White Neumann Logo
• Bass Management Enabled
• LFE Gain 10 dB
• Dimensions (H x W x D): 50 x 120 x 153 mm
• Weight: 350 g

With nine different directional characteristics, the M 149 Tube can be adapted to very different acoustic recording situations. Like its ancestors, it is particularly suitable for speech and song. This is not only due to its capsule, but also the particularly low replacement noise level of its modern circuit technology.

The M 149 tube is discussed from the side. Its front side is marked by the company nameplate and the directivity switch. Below the capsule, a dome ensures dispersion of sound from the upper half-space, so there is no disturbing interference with the direct sound components. To protect against structure-borne sound, the capsule is elastically mounted. The capsule is surrounded by the large microphone basket of the old M 49, which is now acoustically more open and behaves sound-neutral.

There are nine characteristics to choose from: Omnidirectional, wide cardioid, cardioid, hyper cardioid and figure eight, each with an intermediate position.

Unlike other tube microphones, the M 149 Tube combines a specially selected tube (triode) with state-of-the-art circuitry. The aim of the development was to use the special transmission characteristics of a tube and to bring the hereby amplified capsule signal controlled, unadulterated and feedback-free to the microphone output. Therefore, the usual in tube microphones output transformer is not used. Instead, to drive the different output loads, a particularly suitable for audio signals integrated amplifier with very low distortion (THD

On the back of the microphone is another slide switch. It operates a high-pass filter whose cut-off frequency (3 dB) can be selected in half-octave steps between 20 Hz and 160 Hz. In this way disturbances of air conditioners or impact sound can be faded out in a very targeted manner. In addition, e.g. the volume of a voice can be flexibly measured using the proximity effect.

The M 149 Tube is powered by an 8-core cable from its special N 149 power supply. At its output, the microphone signal is on a 3-pin XLR connector. The microphone is supplied in an aluminium case as a set together with the 8-pin microphone cable, the power supply N 149 and the elastic suspension EA 170.

• Acoustic operation Pressure gradient receiver
• Polar pattern: Omnidirectional, cardioid, wide cardioid, hyper cardioid, figure eight and one intermediate position each
• Transmission range: 20 Hz ... 20 kHz
• Field transmission factor at 1 kHz at 1 kOhm: 34/47/62 mV / Pa (Omnidirectional, / cardioid / figure eight)
• Nominal impedance: 50 ohms
• Nominal load impedance: 1000 ohms
• Replacement noise level CCIR468-3: 28/25/23 dB (omnidirectional / cardioid / figure eight)
• Replacement noise level DIN / IEC651: 16/13/11 dB-A
• Noise level CCIR 468-3: 66/69/71 dB
• Noise level DIN / IEC651: 78/81/83 dB
• Limit sound pressure level (tube characteristic) for K
• Maximum output voltage 18 dBu
• Dynamic range of the amplifier DIN / IEC651 for K
• Power Supply Power Supply N 149
• Weight 730 g
• Diameter 70 mm length 201 mm
• Including aluminium case, 8-pin microphone cable, power supply N 149 A, elastic suspension EA 170, dust bag

• Cardioid
• Frequency range: 20 - 20.000 Hz
• Impedance: 50 Ohm
• Maximum level: 132 dB SPL max.
• 48V Phantom power
• Colour: Black
• XLR connector
• Weight: 300 g
• Delivery incl. neoprene bag and microphone holder

Bundle offer comprising

• Condenser Vocal Microphone
• Cardioid
• Frequency range: 20 - 20.000 Hz
• Impedance: 50 Ohm
• Maximum level: 132 dB SPL max.
• 48V Phantom power
• Colour: Black
• XLR connector
• Weight: 300 g
• Delivery incl. neoprene bag and microphone holder

• Professional microphone cable
• Length: 6 m
• Original Neutrik NC 3 FXX-BAG + NC 3 MXX-BAG XLR plug
• Cable type: CME 220 Black
• Includes hook and loop fastener
• Colour: Black

• 6.5" Woofer
• 1" Tweeter
• DSP-controlled electronics
• Room-adaptive calibration via Neumann's Automatic Monitor Alignment MA 1 (optional, not included in the delivery)
• Switch for a manual room correction
• Frequency response (±3 dB): 39 - 21,000 Hz
• Amplifier: 100 W / 145 W
• Electronic peak/thermo limiter protected circuit are separated for the tweeter and the woofer
• Bass reflex cabinet
• Integrated switching power supply 100-240V, 50/60 Hz
• 1 Line input: XLR
• S/PDIF coaxial
• 2 Ethernet connections: AES67 and Control Network
• Dimensions (H x W x D): 345 x 225 x 273 mm
• Weight: 8 kg

Bundle offer comprising

• Condenser Vocal Microphone
• Optimised for female voices in rock and pop area
• Polar pattern: Cardioid
• Frequency range: 20 - 20.000 Hz
• Impedance: 50 Ohm
• Requires 48V phantom power
• XLR connector
• Weight: 300 g
• Colour: Black
• Delivery incl. neoprene bag and microphone holder

• One-hand microphone stand
• Very sturdy one-hand microphone stand with light round steel base Ø 275 mm
• Easily adjustable by one-hand mechanism
• "Elegance" Series
• Height: 1055 - 1735 mm
• Impact sound absorbing rubber profile
• Steel
• 3/8" Threaded connector
• Weight 3.0 kg
• Colour: Black
• Matching bag under Art. 263921
• Winner of the Red Dot Design Awards 2013

• Professional Microphone Cable
• XLR male > XLR female
• 2 x 0.38 mm² cable profile
• Double copper spiral shielding
• Neutrik NC3MX-SOM connectors
• Length: 10 metres
• Colour: Black

• 6.5" Woofer
• 1" Tweeter
• DSP-controlled electronics
• Room-adaptive calibration via Neumann's Automatic Monitor Alignment MA 1 (optional, not included in the delivery)
• Switch for a manual room correction
• Frequency response (±3 dB): 39 - 21,000 Hz
• Amplifier: 100 W / 145 W
• Electronic peak/thermo limiter protected circuit are separated for the tweeter and the woofer
• Bass reflex cabinet
• Integrated switching power supply 100-240V, 50/60 Hz
• Connections: 1x XLR line input
• S/PDIF coaxial
• Ethernet connection
• Dimensions (H x W x D): 345 x 225 x 273 mm
• Weight: 8 kg
• Colour: White

• For M147, TLM 103, TLM 193
• Colour: White

• Wired
• Circumaural
• Open
• Dynamic
• Frequency range: 12 - 34,000 Hz
• Impedance: 120 Ohm
• Sound pressure level: 103 dB SPL/1kHz/1Vrms
• 38 mm Neodymium transducer
• Maximum power handling: 1000 mW
• Rated power handling: 200 mW
• Distortion factor at 1 kHz and 100 db SPL
• Replaceable fabric foam ear pads
• Single-sided cable routing
• Replaceable 3 m smooth cable with 3.5 mm jack connector
• Weight (without cable): 352 g
• Incl. adapter 3.5 mm to 6.3 mm jack and carrying bag

• 24-Bit 48 kHz signal processing
• Equipped with: 4" woofer 1" tweeter
• Frequency response (+/- 3 dB): 57 Hz - 21 kHz
• Maximum output level: 108.8 dB SPL
• Power: 90 W woofer and 50 W tweeter
• Control panel for standby and acoustical control
• Electronic peak /thermo limiter protection circuit separately for woofer and tweeter
• Input / output level control
• Linear phase DSP crossover 8th order
• External 4-position acoustical controls for low-mid or internal automatic or manual room correction (Precision Alignment) with max. 8 IIR filters plus low / high shelf global filter balance
• 70-ms delay function for time and lipsync settings
• Self-generated noise
• Input: balanced XLR, magnetically shielded
• Network connection
• 2x M6 threaded receivers for stands/mounts
• Dimensions (H x W x D): 233 x 154 x 194 mm
• Weight: 3.5 kg
• Colour: White

• Colour: Nickel
• 2 Condenser miniature microphones KM 183
• Frequency range: 20 - 20000 Hz
• Impedance: 50 Ohm
• Max SPL: 140 dB
• Polar pattern: Hypercardioid
• Frequency range 20 Hz ... 20 kHz
• Sensitivity 12mV/Pa
• Required phantom power 48 V +/- 4 V
• Diameter: 22 mm
• Length: 107 mm
• Weight: each approx. 80 g
• Incl. 2 pieces WNS 100 windshield and 2 SG 21 stand joints

• Neumann (Klein + Hummel)
• With 35 mm high stand sleeve
• For mounting on standard 35 mm diameter high stands
• Mounting of other speakers with appropriate attachments
• For LH 12, LH 15, LH 25, LH 26, LH 31, LH 34, LH 35, LH 36, LH 38, LH 80, CL 80
• Colour: Black

• Large diaphragm microphone based on the K87 capsule
• Cardioid
• Frequency range: 20 Hz - 20 kHz
• Equivalent noise level (A-weighted1) 7 dB-A
• SPL is ideally suited for THD
• Nominal Impedance: 50 Ohm
• Due to the minimal inherent-noise it is ideally suited for: broadcasters, very quiet instruments, radio plays, sound recording / sampling, home recording
• Is great as a spot microphone and for reducing the sound in e.g. wind instruments, strings, percussion, guitar amps, drum overhead positions
• Colour: Nickel
• Dimensions: diameter 60 mm x length 132 mm
• Weight approx. 450 g
• Includes 1x EA1 elastic suspension together with high-quality cardboard packaging - but without a wooden case and rigid support
• Suitable optional case: Art.494135 (not included)

• Universally applicable studio microphone
• Pressure gradient receivers can be used for vocals, speakers, overhead and wind instruments
• Switchable polar pattern: omnidirectional, wide cardioid, cardioid, hypercardioid, figure eight
• Switchable 10 dB attenuation
• Two-stage bass roll-off
• Frequency range: 20 - 20,000 Hz
• Nominal impedance: 150 ohms
• Nominal load impedance: 1000 ohms
• Max. sound pressure level for K
• Requires + 48V phantom power
• Dimensions (length x diameter): 185 x 46 mm
• Weight: 400 g

• Neumann TLM 102 Microphone
• 1x Shock mount EA-4

• Pressure gradient transducer
• Directional characteristic: Cardioid
• Frequency range: 20 Hz - 20 kHz
• Peak SPL: 144 dB
• Nominal impedance: 50 Ohm
• Rated load impedance: 1 kOhm
• Equivalent noise level, A-weighted: 12 dBA
• Required 48 V Phantom power
• Weight: approx. 260 g
• Diameter: 52 mm
• Length: 116 mm
• Colour: Black
• Suitable optional case: Art.494135 (not included)

• 2 Independent large diaphragm systems with 5 directional characteristics: Omnidirectional, Wide Cardioid, Cardioid, Hypercardioid, Figure-8
• Upper capsule rotates against the lower capsule over 270°
• Frequency response: 20 - 20,000 Hz
• Max. SPL (sound pressure level) for k
• Extremely low inherent self noise with only 13 dB-A according to DIN/IEC 651
• Transformer-balanced circuit
• Dimensions (diameter x length): 30 + 48 mm x 293 mm
• Weight: 510 g
• Colour: Black

Note: Requires +48 V of phantom power.

• For Neumann EA 4 microphone spider
• Shipping quantity: 2 Pieces

Bundle offer comprising

• Large diaphragm condenser microphone
• Pressure gradient transducer
• Directional characteristic: Cardioid
• Frequency range: 20 Hz - 20 kHz
• Peak SPL: 144 dB
• Nominal impedance: 50 Ohm
• Rated load impedance: 1 kOhm
• Equivalent noise level, A-weighted: 12 dBA
• Maximum output voltage: 13 dBu
• Sensitivity at 1 kHz into 1 kohm 11 mV/Pa
• 48 V ± 4 V Phantom power required
• Diameter 52 mm
• Length 116 mm
• Weight approx. 260 g
• Colour: Nickel

• Microphone Stand with Boom Arm
• Cast base with foldable feet
• Metal tommy screw on the boom joint
• 3/8" Threads for microphone clamp
• Includes 3/8" to 5/8" thread adapter
• Height adjustable from 105 - 170 cm
• Adjustable arm: 75 cm
• Colour: Black

• Mounting Popkiller
• With elastic arm
• Arm length: 20 cm
• Edge-Ring: Ø 15.5 cm
• Nylon-Cover: Ø 14 cm

• Microphone Cable
• Length: 5.0 m
• XLR 3-pin male to XLR 3-pin female
• Conductor area: 2x 0.22 mm²
• PVC sheath
• 95% Covered
• Diameter: 6.0 mm
• Colour: Black

• Length: 115 mm
• As an attachment for speaker stands
• Colour: Black RAL 9005
• Ink. Small parts for fastening and 2x Allen keys