Multiple, Divider Modules

• Performance switcher and router
• 4 Inputs and outputs for audio and CV signals
• 3-Way toggle switch per channel (pushbutton / off / switch)
• Normalised inputs A-D
• Input A normalized to +5 V to generate manual trigger and gate signals
• Upper section with 2 outputs and selectable input A-D via rotary switch
• Power requirement: 25 mA (+12 V) / 25 mA (-12 V)
• Width: 8 HP
• Depth: 43 mm

• Each of the 6 sockets can be switched to X, Y or Off via toggle switch
• Link connector on the rear allows connection to further Switched Mult 1U or XY IO 1U modules
• Width: 14 HP
• Depth: 18 mm

• Eight interconnected jacks can be split into 2 groups (solder bridge on the assembly side)
• Width: 2 HP
• Vintage edition with black front plate

Tiptop Audio Wayout8; Eurorack module; patchbay module for organizing signals between multiple Eurorack cases or between a Eurorack system and DAW; 8 inputs and outputs; suitable for audio, CV and gate/trigger signals; grounded inputs to avoid unwanted noise; passive module (no power required); width: 6 HP; depth: 10mm

• Binary phase accumulator
• Component of the Leibniz subsystem - can be combined with Drezno, Jena, Odessa and Lipsk
• Works as clock and audio divider with 8 outputs, bidirectional binary counter, digital oscillator and more
• Inputs for reset and 2x clock signal (ascending and descending)
• Outputs: 8 bit
• Current: 25 mA (+12V) / 30 mA (-12V)
• Width: 6 HP

• Dual Passive Multiple
• Contains two independent adapters with three 3.5 mm mono jacks to two 6.3 mm mono jacks
• Passive construction - requires no power supply
• Width: 4 HP
• Depth: 28 mm

At the output, the A-115 provides the sum mix of original and sub-octaves. You can adjust the amount (i.e., the amplitude) of the original signal and each sub-octave individually with an attenuator. The sub-octaves generated by the A-115 are symmetric square-wave signals. A sum mix of the four square-wave signals and the original signal is available at the output.

• Width: 8HP / 40.3 mm
• Depth: 40 mm (measured from the rear of the front plate)
• Power requirements: 20 mA (12V) / -10 mA (-12V)

• Contains 5 independent adapters from 3.5 mm mono jack to 6.3 mm mono jack
• Passive construction - no power supply required
• Width: 8 TE

• Dual 1x5 passive
• Width: 14 HP
• Power Requirements: 0 mA

• Universal module for mixing, inverting, distributing and dividing control voltages and signals
• Two independent 1: 4 buffered multiples
• Two voltage transformers
• 4: 1 Summer
• Power consumption: 50 mA
• Dimensions: 6 HP

• Voltage controllable clock divider with 8 outputs
• Clock and reset input
• 8 Clock outputs with even and odd divider factors
• Rotate CV input (range 0V to +5V) shifts the different dividers at the output sockets
• Configurable via jumpers: gate/trigger mode, extended division up to /64, spread mode, auto reset, counting direction ascending or descending
• Expandable with 4ms RCD breakout module (art. 545216)
• Current consumption: 33mA (+12V) / 4mA (-12V)
• Width: 4 TE
• Depth: 35 mm

• Passive multiple distributor
• Dual 1-to-3 Multiple
• Width: 4 HP
• Depth: 23 mm

• 8x Interconnected jacks
• Sockets are divided into 2x quadruple groups; but can also be modified to an eight-multiple (soldering bridge on the circuit board)
• Width: 2HP

• Contains two 6.3mm / 3.5mm multiples, each with a 6.3mm and 2 x 3.5mm jack jacks
• One multiple is mono (ie the two small jack sockets are connected to the tip of the 6.3 mm jack socket)
• The other is connected in stereo (ie one of the two small jacks is connected to the tip, the other to the ring of the 6.3 mm jack).

• Buffered precision multiple
• 1-on-3 or 1-on-6 multiple with active electronics for audio and CV signals
• Also distributes pitch CV to the cent
• Current requirement: 20 mA (+12 V / 20 mA (-12 V)
• Width: 2 HP
• Depth: 40 mm

• 6-Channel Clock Divider
• 6 Independent clock dividers (divided into section A & B) with adjustable divider factor per channel
• Clock multiplication for section A switchable
• Alternative clock source for section B selectable
• 2 Logic links between section A & B selectable
• Divider B6 switchable as reset for section A and/or B
• Clock and reset input
• 6 Divider outputs
• Current consumption: 20 mA (+12 V) / 0 mA (-12 V)
• Width: 8 HP
• Depth: 22 mm

• Multiple with two sections
• Passive 1-to-6 multiple
• Buffered multiple with normal and inverted input and 5 outputs
• Current consumption: 1 mA (+12 V) / 1 mA (-12 V)
• Width: 6 HP
• Depth: 25 mm

• Quad buffer
• Contains 4 separate control voltage buffers
• For use with the outputs of switches, quantizers, sequencers, S & H modules, and more
• Outputs are normalised to the next input
• Use as a buffered multiple possible
• Width: 4 HP

• Quad Passive Multiple
• Four-channel 1-to-3 or two-channel 1-to-6 multiple
• Passive design - does not require power supply
• Width: 4 HP
• Depth: 14 mm